Ulica M5STACKamp-S3Bat Embedded Core Module
Opis
Stamp-S3Bat is an embedded core module integrated with power management. It utilizes the ESP32-S3-PICO-1-N8R8 as the main control core, supports 2.4GHz Wi-Fi, and comes with built-in 8MB Flash and 8MB PSRAM.
It provides 11 GPIO pins, an onboard battery power interface, and can be directly connected to an external 3.7V lithium battery for power supply.
With an efficient built-in PMIC and multi-level power control design, it supports power input and output control, as well as status monitoring for input voltage in voltage. It supports external low-power wake-up. After the main controller shuts down and enters low-power sleep mode, it can be triggered to wake up via an external PMIC wake-up IO. The module features an onboard user button and a programmable RGB LED. With 2.54mm standard-pitch half-hole solder pads, it can be integrated into your applications through SMT, DIP, or other methods, helping developers quickly build IoT applications.
Specifikacije
Hitri začetek
Priprava
- Obiščite uradno spletno stran Arduina webspletno mesto in namestite Arduino IDE
https://www.arduino.cc/en/Main/Software - Dodajte naslednjega upravitelja upravnega odbora URL do File → Nastavitve → Upravitelj dodatnih tabel URLs:
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
- Odprite Upravitelj plošč, poiščite »ESP32« in kliknite namesti.
- After installation, select the board “ESP32S3 Dev Module”.
- Configure the following options. USB CDC On Boot: “Enabled”, PSRAM： “OPI PSRAM”, USB Mode: “Hardware CDC and JTAG"
Wi-Fi Scan
- Izberite prampprogram »Ex«amples” → “WiFi” → “WiFiScan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
- After uploading is complete, open the Serial Monitor to view Informacije o iskanju omrežij Wi-Fi.
BLE skeniranje
- Izberite prampprogram »Ex«amples” → “BLE” → ”Scan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
- After uploading is complete, open the Serial Monitor to view Informacije o skeniranju BLE.
Opozorilo FCC
Opozorilo FCC:
Vse spremembe ali modifikacije, ki jih ni izrecno odobrila stranka, odgovorna za skladnost, lahko razveljavijo uporabnikovo pooblastilo za uporabo opreme.
Ta naprava je skladna s 15. delom pravil FCC. Delovanje je odvisno od naslednjih dveh pogojev:
- This device may not cause harmful interference, andThiss device must accept any interference received, including interference that may cause undesired operation.
POMEMBNA OPOMBA:
Opomba: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use,s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Preusmerite ali premaknite sprejemno anteno.
- Povečajte razdaljo med opremo in sprejemnikom.
- Priključite opremo v vtičnico na drugem tokokrogu kot tisti, na katerega je priključen sprejemnik.
- Za pomoč se posvetujte s prodajalcem ali izkušenim radijskim/TV tehnikom.
Izjava FCC o izpostavljenosti sevanju:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated wita h minimum distance of 20cm between the radiator & your body.
Pogosto zastavljena vprašanja
Q: Can I power the Stamp-S3Bat using a different voltage baterija?
A: It is recommended to use a 3.7V lithium battery as the input power source for the Stamp-S3Bat to ensure optimal performance and compatibility.
Q: How many GPIO pins does Stamp-S3Bat provide?
A: Stamp-S3Bat provides a total of 11 GPIO pins for connecting external devices and sensors.
Q: What is the operating temperature range of Stamp-S3Bat?
A: The operating temperature range of Stamp-S3Bat is not specified in the user manual. It is advisable to operate within normal room temperature conditions for best results.
Dokumenti / Viri
 |
Ulica M5STACKamp-S3Bat Embedded Core Module [pdf] Uporabniški priročnik Stamp-S3Bat, Stamp-S3Bat Embedded Core Module, Embedded Core Module, Core Module |