Navodila za uporabo M5StickC Plus2
Tovarniška vdelana programska oprema
Ko naprava naleti na težave z delovanjem, lahko poskusite znova naložiti tovarniško vdelano programsko opremo, da preverite, ali je prišlo do okvare strojne opreme. Glejte naslednji vodič. Za namestitev tovarniške vdelane programske opreme v napravo uporabite orodje za posodobitev vdelane programske opreme M5Burner.
pogosta vprašanja
V1: Zakaj je zaslon mojega M5StickC Plus2 črn/se ne zažene?
rešitve: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
V2: Zakaj deluje le 3 ure? Zakaj se 100 % napolni v 1 minuti, če odstranite polnilni kabel, se bo izklopil?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
Priprava
- Refer to the M5Burner tutorial to complete the firmware flashing tool download, and then refer to the image below to download the corresponding firmware.
Povezava za prenos: https://docs.m5stack.com/en/uiflow/m5burner/intro
Namestitev gonilnika USB
Driver Installation Tip
Click the link below to download the driver matching your operating system. The driver package for the CP34X (for the CH9102 version) can be downloaded and installed by selecting the installation package corresponding to your operating system. If you encounter issues with program download (such as timeout or “Failed to write to target RAM” errors), try reinstalling the device driver.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Port Selection on MacOS
On MacOS, there may be two available ports. When using them, please select the port named wchmodem.
Izbira vrat
Napravo priključite na računalnik prek kabla USB. Ko je namestitev gonilnika končana, lahko v programu M5Burner izberete ustrezna vrata naprave.
Zažgite
Kliknite »Zapiši«, da začnete postopek utripanja.
StickC-Plus2
Šifra artikla: K016-P2
Opis
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Vadnica
UIFlow
Ta vadnica bo predstavila, kako upravljati napravo StickC-Plus2 prek grafične programske platforme UIFlow.
UiFlow2
Ta vadnica bo predstavila, kako upravljati napravo StickC-Plus2 prek grafične programske platforme UiFlow2.
Arduino IDE
Ta vadnica bo predstavila, kako programirati in upravljati napravo StickC-Plus2 z uporabo Arduino IDE.
Opomba
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Lastnosti
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Vgrajen mikrofon
- User buttons, 1.14-inch LCD, power/reset button
- Li-ionska baterija 200 mAh
- Razširitveni priključek
- Integrated passive buzzer
- Wearable & mountable
- Razvojna platforma
- UiFlow1
- UiFlow2
- Arduino IDE
- ESP-IDF
- PlatformIO
Vključuje
- 1 x StickC-Plus2
Aplikacije
- Nosljive naprave
- IoT controller
- STEM education
- DIY projekti
- Naprave za pametni dom
Specifikacije
| Specifikacija | Parameter |
| SoC | ESP32-PICO-V3-02 240 MHz dvojedrni procesor, Wi-Fi, 2 MB PSRAM-a, 8 MB bliskovnega pomnilnika |
| Vhodna voltage | 5 V pri 500 mA |
| Vmesnik | 1x priključek tipa C, 1x priključek GROVE (I2C + V/I + UART) |
| LCD zaslon | 1.14-palčni barvni TFT LCD-zaslon z ločljivostjo 135 x 240, ST7789V2 |
| Mikrofon | SPM1423 |
| Gumbi | Uporabniški gumbi x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Brenčalo | Vgrajen pasivni brenčalo |
| IMU | MPU6886 |
| Antena | 2.4G 3D antena |
| Zunanji zatiči | G0, G25/G26, G36, G32, G33 |
| Baterija | 200 mAh pri 3.7 V, v notranjosti |
| Delovna temp | 0 ~ 40 °C |
| Ohišje | Plastika (PC) |
| Velikost izdelka | 48.0 x 24.0 x 13.5 mm |
| Teža izdelka | 16.7 g |
| Velikost paketa | 104.4 x 65.0 x 18.0 mm |
| Bruto teža | 26.3 g |
Navodila za uporabo
Vklop/izklop
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Sheme
Zemljevid pripenjanja
Rdeča LED in IR oddajnik | Gumb A | Gumb B | Brenčalo
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Gumb A | Gumb A | ||||
| Gumb B | Gumb B | ||||
| Gumb C | Gumb C | ||||
| Pasivni piščal | Brenčalo |
Barvni zaslon TFT
Driver IC: ST7789V2
Ločljivost: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| TFT zaslon | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Mikrofon MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | PODATKI |
6-osni IMU (MPU6886) in RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| IR oddajnik | TX | ||
| Rdeča LED | TX |
HY2.0-4P
| HY2.0-4P | Črna | Rdeča | Rumena | Bela |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Velikost modela
Podatkovni listi
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU6886
SPM1423
Programska oprema
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Hitri začetek
UiFlow2
StickC-Plus2 UiFlow2 Hitri začetek
PlatformIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
okvir = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
gonilnik USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Ime voznika | Supported Chip | Prenos |
| CH9102_VCP_SER_Windows | CH9102 | Prenos |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Prenos |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Prenos | Opomba |
| Factory Test for Windows | prenos | / |
drugo
Vodnik za obnovitev tovarniške vdelane programske opreme StickC-Plus2
Video
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Sprememba različice
| Datum izdaje | Spremeni opis | Opomba |
| / | Prva izdaja | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Primerjava izdelkov
Razlike v strojni opremi
| Izdelek Ime |
SoC | Upravljanje napajanja | Kapaciteta baterije | Spomin | Čip USB-UART | barva |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB bliskovnega pomnilnika | CH522 | Red- orange |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB bliskovnega pomnilnika | CH9102 | Oranžna |
Razlike med pritiski
| Ime izdelka | IR | LED | TFT | GUMB A | GUMB B | GUMB C (ZBUDI SE) |
PRIDRŽI | Baterija voltage Zaznaj |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) KLK (G13) enosmerni tok (G23) RST (G18) CS (G5) |
G37 | G39 | Redno gumb |
/ | Preko AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) KLK (G13) enosmerni tok (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Razlike pri vklopu/izklopu
| Izdelek Ime | Vklop | Izklop |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Ker StickC-Plus2 ne vsebuje PMIC AXP192, se način vklopa/izklopa razlikuje od prejšnjih različic. Kot smo že omenili na začetku tega dokumenta, je delovanje v veliki meri podobno, vendar se bodo podprte knjižnice razlikovale. Moč signala Wi-Fi in IR sta bili v primerjavi s prejšnjim modelom izboljšani.
Dokumenti / Viri
 |
Razvojni modul za internet stvari M5STACK ESP32-PICO-V3-02 [pdf] Uporabniški priročnik Razvojni modul za IoT ESP32-PICO-V3-02, ESP32-PICO-V3-02, Razvojni modul za IoT, Razvojni modul, Modul |