HYPERKIN Competitor Wired Controller User Manual

HYPERKIN Competitor Wired Controller

Hvala za nakupasing the Hyperkin The Competitor for Xbox Series X|S, Xbox One, and Windows 10/11 PC – Wired Controller. For your safety and the safety of others, please carefully read this guide before using this product.

1. Plug the provided Type-C cable into the Type-C port located on the TOP of the Hyperkin Xenon.
2. Plug the other end of the cable into an available USB port on your Xbox Series X|S, Xbox One, PC or Steam OS.
3. The controller will vibrate.
4. Click the Nexus button.
5. The ring light will illuminate.

Vaš krmilnik je zdaj pripravljen za uporabo.

WAKING UP YOUR XBOX CONSOLE USING THE COMPETITOR

If The Competitor is plugged into an Xbox console, you may turn on the console by clicking the Nexus button on The Competitor. After doing so, the console will turn on and the controller Nexus button will illuminate (this may take a few seconds).

Vaš krmilnik je zdaj pripravljen za uporabo.

PROGRAMMABLE BACK BUTTONS (MAPPING)

To map a button to a back button, hold the Mode Button (marked “M”) on the back of the controller, and your desired back button (M1 or M2) at the same time. The Competitor will vibrate, and the ring light around the Nexus will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the button you would like mapped to your desired back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and the selected button has been mapped to your desired back button.

PROGRAMMABLE BACK BUTTONS (UN-MAPPING)

To un-map a button from a back button, hold the Mode Button (marked “M”) and your desired back button. The Competitor will vibrate, and the ring light will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the same back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and a button is no longer mapped to that back button.

BACK BUTTON LOCKS

To disable back buttons, slide the switches on the back of The Competitor inwards towards the “locked” indicator to lock the back buttons. Slide outwards to unlock.

REMOVEABLE STICK CAPS
Grip and remove the stick caps in an upward motion. To set new stick caps onto the sticks, align the smaller teeth on the stick caps with the notches on the stick. Press down on the stick caps until they click into place.

SLUŠALKE
Connect your headset audio jack into the bottom of The Competitor.

GUMB ZA IZKLOP MIK
Double-tap the Mute Button (microphone symbol) on the front of The Competitor to mute the microphone on a connected headset. An orange glow indicates that your microphone is muted.

Obvestilo FCC

Ta oprema je bila testirana in ugotovljeno je bilo, da je v skladu z omejitvami za digitalne naprave razreda B v skladu s 15. delom pravil FCC. Te omejitve so zasnovane v stanovanjski namestitvi. Ta oprema ustvarja, uporablja in lahko oddaja radiofrekvenčno energijo in lahko povzroči škodljive motnje radijskih komunikacij, če ni nameščena in uporabljena v skladu z navodili. Vendar ni nobenega zagotovila, da do motenj ne bo prišlo pri določeni namestitvi. Če ta oprema povzroča škodljive motnje pri radijskem ali televizijskem sprejemu, kar je mogoče ugotoviti z izklopom in vklopom opreme, uporabnika spodbujamo, da poskusi odpraviti motnje z enim ali več od naslednjih ukrepov:

• Preusmerite ali premaknite sprejemno anteno.
• Povečajte razdaljo med opremo in sprejemnikom.
• Priključite opremo v vtičnico na drugem tokokrogu kot tisti, na katerega je priključen sprejemnik.
• Posvetujte se s prodajalcem ali izkušenim tehnikom radijske televizije ali po e -pošti Support@Hyperkin.com za pomoč. Za zagotovitev skladnosti z omejitvami FCC razreda B morate uporabiti zaščitene kable.

Spremembe ali modifikacije te enote, ki jih stranka, odgovorna za skladnost, ni izrecno odobrila, lahko razveljavijo uporabnikovo pooblastilo za uporabo te opreme.

Izjava o skladnosti z EU direktivo

Hyperkin Inc., located at 1939 West Mission Blvd, Pomona, CA 91766, declares under our sole responsibility that the product, Hyperkin Xenon Wired Controller, is in compliance with the essential requirements and other relevant provisions of Low Voltage Direktiva (LVD) 2014/35/EU, Direktiva RoHS 2011/65/EU in ima oznako CE.

Celotno izjavo o skladnosti lahko zahtevate po elektronski pošti:

• E-pošta: compliance@hyperkin.com
• Ime podjetja: Hyperkin Inc.
• Naslov: 1939 West Mission Blvd, Pomona, CA 91766

© 2026 Hyperkin Inc. Hyperkin® is a registered trademark of Hyperkin Inc. All rights reserved. All other trademarks are the property of their respective owners.