FlySpark F4 V1 Stack Flight Controller
Specifikacije
- Ime izdelka:
FlySpark F4 V1 BLS 60A sklad - Lastnosti AI:
Sensor Fusion, PID Autotuning, Adaptive Filtering - Podpora za programsko opremo:
Betaflight, INAV, Ardupilot, EMU-let, SkyBrush - ESC Communication:
BLHeli_S Bluetooth in USB-C - Povezljivost:
3-6S LiPo - Dimenzija:
47.8 mm (D) x 47.5 mm (Š) x 18.3 mm (V) - Montaža:
30.5 x 30.5 mm z velikostjo luknje 4 mm - Teža:
34 g
Navodila za uporabo izdelka
Krmilnik leta FlySpark F4 V1
Postavitev:
Refer to the user manual for the layout of the flight controller.
Periferna povezava:
Connect peripherals as per the provided diagram.
Konfiguracija aplikacije in FC:
Use the recommended apps and follow the configuration instructions.
Posodobitev vdelane programske opreme FC:
Connect the flight controller to a PC via USB for firmware updates.
FLYSPARK BLS 60A 4-v-1 ESC
Postavitev:
Check the layout guide in the manual for proper installation.
Povezava z motorji in napajalnim kablom:
Connect motors and power cables securely.
Konfiguracija ESC-ja:
Use the FlySpark app for ESC configuration settings.
Posodobitev vdelane programske opreme ESC:
Follow the provided steps to update the firmware for ESC.
FlySpark F4 V1 BLS 60A sklad
Specifikacije Konecview
Paket
- FlySpark F4 V1 Flight Controller x 1
- FlySpark BLS 60A 4-in-1 ESC x 1
- 35 V 1000 uF kondenzator z nizkim ESR x 1
- M3 najlonska matica x 4
- SH 1.0 mm dolžine 25 mm 8pin kabel (za povezavo FC-ESC) x 1 SH 1.0 mm dolžine 75 mm 6pin kabel* x 1
- M3*30 mm notranji šestrobi vijaki x 4
- DJI 6pin kabel (80 mm) x 1
- Napajalni kabel XT60 (100 mm) x 1
Diagram povezave FC
Vodnik za povezave FC in ESC
1. način:
- Using 8.Pin JST Cable
2. način:
Neposredno spajkanje
- Na 8 kontaktnih ploščic na vsakem koncu prispajkajte 8 žic, pri čemer upoštevajte spodnje definicije kontaktnih ploščic.
Specifikacije krmilnika leta
- Uporabite 6-polni kabel, ki je priložen zračni enoti O3
- Uporabite 6-pinski kabel, ki je priložen paketu FlySpark F4 V1 BLS 60A.
F C Firmware update
To update the firmware for your FlySpark F4 VI flight controller, please follow these steps:
Connect the Flight Controller to Your PC:
- Use a USB cable to connect the FlySpark F4 VI flight controller to your PC
Open Betaflight I INAV Configurator.
- . Launch the Betaflight Configurator or INAV Configurator on your PC. For this guide, we’ll use Betaflight Configurator as an example.
Navigate to Firmware Flashing:
- In the Betaflight Configurator, navigate to the ‘Firmware Flashing’ page.
Select Target and Flash Firmware:
- Choose the target firmware for ‘Flyspark F4 VI’ from the dropdown menu.
- Initiate the firmware flashing process.
Opomba:
The Flyspark F4 VI flight controller does not support wireless firmware flashing. It must be performed using a USB connection to your PC.
Flyspark BLS 60A 4-in-l ESC
Povezava z motorji in napajalnim kablom
ESC Specs FlySpark F4 V1 BLS 60A Stack
Posodobitev vdelane programske opreme ESC
Ta 8-bitni 50A ESC je predhodno naložen s programsko opremo BLHeliS, vendar ga je mogoče posodobiti tudi s programsko opremo Bluejay, ki ponuja filtriranje vrtljajev in podporo za dvosmerni Dshot. Za posodobitev programske opreme sledite tem korakom:
- Prepare Your Drone:
Remove all propellers from your drone for safety. - Connect ESC to Flight Controller:
Ensure the flight controller is properly connected to the ESC, then power up the drone. This step ensures the ESC initializes correctly. - Povežite se z računalnikom:
Use a USB Type-C cable to connect the flight controller to your computer. - Access Firmware Configuration:
Open the Chrome browser and visit: www.esc-configurator.com - Flashing Steps:
Follow the firmware flashing steps displayed on the configurator website. Ensure you select the appropriate options for flashing to Bluejay firmware.
POZOR:
- PROPELLERS OFF: REMOVE ALL PROPELLERS.
- SECURE CONNECTION: ENSURE SECURE ESC CONNECTION.
- FOLLOW STEPS: FOLLOW FLASHING INSTRUCTIONS CAREFULLY.
- STABLE POWER: ENSURE STABLE POWER SUPPLY.
- www.FlySpark.in
pogosta vprašanja
Kako posodobim vdelano programsko opremo ESC?
To update the ESC firmware, follow these steps: 1. Prepare Your Drone: Remove all propellers for safety. 2. Connect ESC to Flight Controller: Ensure proper connection to the ESC and power up.
Dokumenti / Viri
 |
FlySpark F4 V1 Stack Flight Controller [pdfUporabniški priročnik F4 V1, BLS 60A, F4 V1 Stack Flight Controller, F4 V1, Stack Flight Controller, Flight Controller, Controller |