MC701 LCD Display Thermostat Heating Temperature Controller User Manual

1. Izdelek je končanview

The SINOTIMER MC701 is a versatile digital PID temperature controller designed for precise heating and cooling applications. It features an LCD display, supports various input types including PT100 and K-type thermocouples, and provides SSR/Relay output with alarm functions. This manual provides essential information for the safe and effective operation of your MC701 controller.

Slika 1.1: Spredaj view of the MC701 controller showing the PV and SV displays, and control buttons.

Slika 1.2: Pod kotom view of the MC701 controller, highlighting the model number (MC701-611) and default input type (K).

2. Ključne značilnosti

• High-precision digital PID temperature control.
• Dual LCD display for Process Value (PV) and Set Value (SV).
• Supports multiple input types: K-type thermocouple, PT100 RTD.
• SSR (Solid State Relay) and Relay output options.
• Configurable heating and cooling control modes.
• Integrated alarm functions (ALM1, ALM2).
• Temperature unit selection: Celsius (°C) or Fahrenheit (°F).

3. Varnostne informacije

Pred namestitvijo in uporabo preberite in razumite vsa varnostna navodila. Neupoštevanje teh navodil lahko povzroči električni udar, požar ali resne poškodbe.

• Prepričajte se, da je napajalnik voltage matches the controller's specifications (100-240V AC).
• Vse ožičenje mora opraviti usposobljen električar.
• Disconnect power before making any wiring connections or performing maintenance.
• Do not operate the controller in environments with excessive moisture, dust, or corrosive gases.
• Poskrbite za ustrezno prezračevanje, da preprečite pregrevanje.
• This device is not intended for life-support systems or applications where malfunction could lead to severe injury or property damage.

4. Nastavitev in namestitev

Proper installation is crucial for the accurate and reliable operation of the MC701 controller.

4.1 Montaža

The MC701 is designed for panel mounting. Ensure adequate space for ventilation and wiring connections.

Figure 4.1: MC701 controller shown with its included mounting clips for panel installation.

4.2 Žične povezave

Refer to the wiring diagram on the side of the unit and the instructions below for correct connections. Use appropriate gauge wires for all connections.

Figure 4.2: Detailed wiring diagram on the side of the MC701 unit, showing connections for power, sensor input, SSR, and relay outputs.

• Power Supply (85-265VAC): Connect to terminals 8 and 9.
• SSR Output (OUT): Connect to terminals 10 (+) and 11 (-).
• Relay Output (RELAY): Connect to terminals 13 (NO - Normally Open) and 14 (NC - Normally Closed). Terminal 12 is the common (COM).
• RTD Input (PT100): Connect to terminals 4 (A), 5 (B), and 6 (B).
• Thermocouple Input (TC): Connect to terminals 5 (+) and 6 (-).
• Alarm Outputs (AL1, AL2): Connect to terminals 1, 2, and 3.

5. Navodila za uporabo

5.1 Prikaz končanview

The MC701 features a dual display:

• PV (Process Value): Displays the current measured temperature.
• SV (Set Value): Displays the desired target temperature.

Indikatorske lučke:

• OUT: Indicates output status (heating/cooling).
• AT: Auto-tuning indicator.
• ALM1, ALM2: Alarm indicators.

5.2 Funkcije gumbov

• SET: Enters parameter setting mode or confirms a setting.
• < (R/S): Shifts cursor during setting, or resets alarm.
• V (Down Arrow): Decreases value during setting.
• ^ (Up Arrow): Increases value during setting.

5.3 Setting the Target Temperature (SV)

1. Pritisnite NASTAVI button once. The SV display will start flashing.
2. Uporabite ^ in V gumbe za nastavitev želene temperature.
3. Uporabite < button to shift the cursor for faster adjustment.
4. Pritisnite NASTAVI again to confirm the new SV and exit the setting mode.

5.4 Advanced Parameter Settings

To access advanced parameters (e.g., PID parameters, alarm settings, input type, temperature unit), press and hold the NASTAVI button for several seconds until the first parameter code appears on the PV display.

• Uporaba ^ in V to navigate through parameters.
• Pritisnite NASTAVI do view or edit a parameter's value.
• Prilagodite vrednost z ^, V, in <.
• Pritisnite NASTAVI to save the value and return to the parameter list.
• To exit advanced settings, press and hold NASTAVI again, or wait for a timeout.

6. Vzdrževanje

Regular maintenance ensures the longevity and optimal performance of your MC701 controller.

• Cleaning: Wipe the display and casinz mehko, suho krpo. Ne uporabljajte abrazivnih čistil ali topil.
• Ventilation: Ensure the ventilation slots on the sides of the unit are not obstructed to prevent overheating.
• Connections: Periodically check all wiring connections for tightness and signs of wear or corrosion.
• Storage: If storing the unit, keep it in a dry, dust-free environment within its specified operating temperature range.

7. Odpravljanje težav

8. Specifikacije

Slika 8.1: stran view of the MC701 controller displaying its detailed specification label.

9. Garancija in podpora

For technical support or warranty inquiries, please contact SINOTIMER customer service through the retailer or the official SINOTIMER website. Please have your product model number (MC701) and purchase details ready.

This product is manufactured by SINOTIMER.