ACT Dual Hard Drive Docking Station

Uvod

The ACT AC1504 Dual Hard Drive Docking Station provides a convenient and efficient solution for connecting and accessing 2.5-inch and 3.5-inch SATA I/II/III hard drives and SSDs. This device supports high-speed data transfer via USB 3.0 (USB 3.2 Gen1) and features an offline cloning function, allowing you to duplicate drives without a computer connection. It is designed for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Vsebina paketa

Prosimo, preverite, ali so v vašem paketu vsi elementi:

• ACT Dual Hard Drive Docking Station (AC1504)
• Kabel USB 3.0 tipa A do tipa B
• Napajalni adapter
• Uporabniški priročnik (ta dokument)

Image: The ACT AC1504 Dual Hard Drive Docking Station, its power adapter, and the USB 3.0 cable, as included in the package.

Lastnosti izdelka

• Združljivost z dvema ležiščema: Supports all 2.5-inch and 3.5-inch SATA I/II/III HDDs and SSDs up to 12.5mm thickness.
• Visokohitrostni USB 3.0: Utilizes USB 3.2 Gen1 technology for ultra-fast data transfer rates up to 5 Gbps.
• Podpora za UASP: Enhanced performance with USB Attached SCSI Protocol.
• Kloniranje brez povezave: Clone data from one hard drive to another without requiring a computer connection.
• Vsestranska uporaba: Ideal for data transfer, storage expansion, file backup, data recovery, system upgrades, and disk cloning.

Nastavitev

1. Priključite napajanje: Plug the power adapter into the DC input port on the rear of the docking station. Connect the other end of the power adapter to a wall outlet.
2. Vstavite trde diske: Gently slide your 2.5-inch or 3.5-inch SATA HDD/SSD into the drive slots. Ensure the drives are fully seated. For offline cloning, the source drive should be in the 'Source' slot and the target drive in the 'Target' slot.
3. Connect to Computer (for data access): If you intend to use the docking station for data access via your computer, connect the USB 3.0 cable from the docking station's USB port to an available USB port on your computer.
4. Vklop: Flip the ON/OFF switch on the rear of the docking station to the 'ON' position. The power indicator LED will illuminate.

Image: Rear panel of the docking station, illustrating the USB 3.0 port, ON/OFF power switch, and DC power input for connections.

Image: The docking station connected to a laptop via its USB cable, with two hard drives inserted, demonstrating a typical setup for data access.

Navodila za uporabo

A. Data Access Mode (Connected to Computer)

1. Prepričajte se, da je priklopna postaja vklopljena in povezana z računalnikom prek kabla USB 3.0.
2. Insert one or two SATA HDDs/SSDs into the available slots.
3. Your operating system should automatically detect the drives. They will appear as removable storage devices.
4. You can now access, transfer, and manage files on the inserted drives as you would with any other external storage.

B. Offline Cloning Function

The offline cloning function allows you to duplicate a source drive to a target drive without a computer connection.

1. Priprava pogonov: Ensure both the source drive (the drive you want to copy FROM) and the target drive (the drive you want to copy TO) are SATA HDDs/SSDs. The target drive must be equal to or larger in capacity than the source drive.
2. Vstavite pogone: Insert the source drive into the 'Source' slot (HDD1) and the target drive into the 'Target' slot (HDD2).
3. Prekinite povezavo z računalnikom: Ensure the docking station is NOT connected to any computer via USB.
4. Vklop: Turn on the docking station using the ON/OFF switch.
5. Začni kloniranje: Press and hold the 'Clone' button for approximately 3-5 seconds until the cloning progress LEDs (25%, 50%, 75%, 100%) begin to flash.
6. Confirm Cloning: Release the button, then quickly press it again to confirm the cloning process. The cloning process will begin, indicated by the progress LEDs lighting up sequentially.
7. Spremljajte napredek: The LEDs will indicate the cloning progress (25%, 50%, 75%, 100%). All LEDs will remain solid when the cloning process is complete.
8. Ugasniti: Once cloning is complete, turn off the docking station and safely remove the drives.

Pomembno: All data on the target drive will be erased during the cloning process. Back up any important data from the target drive before initiating cloning.

Image: The ACT AC1504 Dual Hard Drive Docking Station with two hard drives inserted, illustrating its dual-bay design and the LED indicators for power, activity, and cloning progress.

Vzdrževanje

• Polnilno postajo vzdržujte čisto in brez prahu. Za čiščenje uporabljajte mehko, suho krpo.
• Naprave ne izpostavljajte ekstremnim temperaturam, vlagi ali neposredni sončni svetlobi.
• Naprave ne poskušajte razstavljati ali popravljati sami. Obrnite se na usposobljeno servisno osebje.
• Always power off the docking station before inserting or removing drives, especially during data transfer, to prevent data corruption.

Odpravljanje težav

• Pogon ni bil zaznan:
  • Ensure the docking station is powered on and the drive is properly seated in the slot.
  • Verify the USB cable is securely connected to both the docking station and your computer.
  • Poskusite se povezati z drugimi vrati USB na vašem računalniku.
  • Check if the drive is initialized and formatted in your computer's Disk Management (Windows) or Disk Utility (macOS).
• Počasen prenos podatkov:
  • Prepričajte se, da ste priključeni na vrata USB 3.0 na računalniku. Vrata USB 2.0 bodo povzročila nižje hitrosti.
  • Preverite, ali vaš operacijski sistem in gonilniki podpirajo USB 3.0 in UASP.
• Kloniranje brez povezave ne uspe ali se ne začne:
  • Ensure the docking station is NOT connected to a computer via USB during cloning.
  • Confirm the target drive's capacity is equal to or larger than the source drive's capacity.
  • Make sure both drives are properly inserted and detected by the docking station (power and activity LEDs should be on).
  • Follow the cloning steps precisely, especially the press-and-hold and quick-press sequence for the 'Clone' button.

Specifikacije

Garancija in podpora

ACT provides reliable connectivity solutions. All ACT products comply with international standards and EU legislation. This product benefits from a factory warranty of 2 to 5 years.

For technical support or warranty claims, please refer to the official ACT webspletnega mesta ali se obrnite na lokalnega prodajalca.

Webspletno mesto: www.act-connectivity.com