Uporabniški priročnik za potopno aluminijasto črpalko Everbilt 1/2 HP s privezanim stikalom

Uvod

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1/2 HP Submersible Aluminum Sump Pump. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.

Varnostne informacije

OPOZORILO: Always disconnect power before servicing or performing any maintenance on the pump.

NEVARNOST: Nevarnost električnega udara. Ta črpalka je opremljena z ozemljitvenim vodnikom in vtičem za ozemljitev. Za zmanjšanje nevarnosti električnega udara se prepričajte, da je priključen samo na pravilno ozemljeno vtičnico z ozemljitvijo.

• Črpalke ne uporabljajte, če je napajalni kabel ali vtič poškodovan.
• Prepričajte se, da je črpalka postavljena na stabilno, ravno površino.
• Ne črpajte vnetljivih ali korozivnih tekočin.
• Otroke in hišne ljubljenčke hranite stran od delujoče črpalke.
• Pri rokovanju s črpalko nosite ustrezno osebno zaščitno opremo (OZO).
• This pump is designed for clear water only.

Konec izdelkaview

The Everbilt 1/2 HP Submersible Sump Pump is designed for efficient water removal from sump basins. It features an aluminum motor housing for effective cooling and a tethered float switch for automatic operation.

Slika 1: Everbilt 1/2 HP Submersible Aluminum Sump Pump. This image shows the black pump unit with its tethered float switch, power cord, and 1-1/2 inch FNPT discharge port. The Everbilt logo is visible on the side of the pump body.

Ključne značilnosti:

• Aluminum motor housing for efficient motor cooling.
• Continuous duty, efficient 115-Volt PSC motor for lower carbon footprint; higher efficiency using less energy to operate.
• 8.25 ft. cord length.
• Submersible for quiet operation.
• 1-1/2 in. FNPT discharge.
• Semi-open thermoplastic impeller passes 3/8 in. solids.
• Zaščita pred toplotno preobremenitvijo.

Nastavitev in namestitev

1. Karter Basin Priprava: Ensure your sump basin has a minimum diameter of 18 inches to accommodate the tethered float switch. Clean the basin of any debris or obstructions.
2. Umestitev: Črpalko postavite na trdno, ravno površino na dnu jaška basin. Ensure the pump is stable and will not tip over during operation.
3. Priključek izpustne cevi: Connect a 1-1/2 inch FNPT (Female National Pipe Thread) discharge pipe to the pump's outlet. It is recommended to use a check valve in the discharge line to prevent water from flowing back into the sump basin ko se črpalka izklopi.
4. Nastavitev plovnega stikala: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to set the desired "on" and "off" water levels. Ensure the float can move freely without obstruction within the sump basin. The switch-on height is approximately 11.81 inches and switch-off height is approximately 3.94 inches, but can be adjusted by tether length.
5. Napajalni priključek: Plug the pump's 8.25 ft. power cord into a properly grounded 115-Volt AC outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety.
6. Testno delovanje: Napolnite zbiralnik basin with water to activate the float switch and ensure the pump turns on and discharges water correctly. Allow the water level to drop to verify the pump turns off automatically.

Navodila za uporabo

The Everbilt 1/2 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and connected to power, the pump will activate when the water level rises to the "on" point and deactivate when the water level drops to the "off" point.

• Samodejno delovanje: The pump is designed for continuous duty and will cycle on and off as needed based on the water level in the sump basin.
• Ročno upravljanje (če je primerno): While primarily automatic, some installations may allow for manual operation by lifting the float switch. Refer to your specific setup for manual control options.
• Spremljanje: Občasno preverite oljno korito basin and pump operation, especially during heavy rainfall, to ensure it is functioning correctly.

Vzdrževanje

Regular maintenance ensures the longevity and reliable operation of your sump pump.

1. Odklop napajanja: Always disconnect the pump from the power source before performing any maintenance.
2. Čisto korito Basin: Periodically remove any debris, dirt, or sediment from the sump basin that could interfere with pump operation or float switch movement.
3. Preverite rotor: Check the pump's impeller for any clogs or damage. The semi-open thermoplastic impeller is designed to pass 3/8 inch solids, but larger debris can cause issues.
4. Preverite plovni stikalo: Ensure the tethered float switch moves freely and is not obstructed by wires, pipes, or debris.
5. Preglejte napajalni kabel: Examine the power cord for any signs of wear, cuts, or damage. Replace if necessary.
6. Prezimovanje (če je primerno): Če se črpalka nahaja na območju z zmrzovalnimi temperaturami in je ne boste uporabljali, jo odstranite izasin, clean it, and store it in a dry, warm place.

Odpravljanje težav

If problems persist after attempting these solutions, please contact Everbilt customer support.

Specifikacije

Garancija in podpora

For warranty information or technical support, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

Za dodatno pomoč lahko obiščete Everbilt brand page on Amazon or consult the retailer where the product was purchased.