Intermatic ET2145CP Electronic Timer Instruction Manual

1. Uvod

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Intermatic ET2145CP Electronic Timer. This device is designed for 24-hour and 365-day operation, capable of handling up to 30 Amps at 120 to 277Vac. Please read this manual thoroughly before installation and use to ensure safe and proper functionality.

2. Pomembne varnostne informacije

OPOZORILO: Nevarnost požara ali električnega udara

• Pred namestitvijo ali servisiranjem odklopite napajanje na odklopnikih ali odklopite stikala.
• Za odklop opreme pred servisiranjem bo morda potrebnih več kot en odklopnik ali izklopno stikalo.
• Namestitev in/ali ožičenje morata biti v skladu z nacionalnimi in lokalnimi zahtevami električnih predpisov.
• Uporaba BAKER conductors ONLY.
• Do NE remove the insulator covering the terminals.

3. Izdelek je končanview

The Intermatic ET2145CP Electronic Timer features a clear digital display and intuitive controls for programming. Key components include:

• Digitalni zaslon: Prikazuje trenutni čas, datum in informacije o programu.
• Gumb MODE: Used to cycle through different programming modes (e.g., time setting, event programming).
• ENTER/NEXT Button: Confirms selections and advances to the next setting.
• Gumbi za VKLOP/IZKLOP: Used for manual override or to set ON/OFF times for programmed events.
• CLEAR MEM Button: Clears all programmed events or settings.
• CLEAR ENTRY Button: Clears the current entry during programming.
• Puščice gor/dol: Adjust values (time, date, event numbers).
• Terminalni blok: Za priključke električnih žic.

4. Navodila za namestitev

Follow these steps for proper installation of the Intermatic ET2145CP Electronic Timer:

1. Odklop napajanja: Before beginning any work, ensure all power to the circuit is disconnected at the main circuit breaker or disconnect switch. Verify with a voltage tester.
2. Dostopne priključne sponke: To access the wiring terminals, lift the plastic insulator covering the terminals. You may need to remove a screw and swing the insulator aside.
3. Žične povezave: Connect the electrical wiring to the appropriate terminals. Ensure all connections are secure and comply with local and national electrical codes. Use only copper conductors.
4. Secure Insulator: Once wiring is complete, replace the plastic insulator covering the terminals and secure it with the screw (if applicable).
5. Obnovi moč: After ensuring all connections are correct and secure, restore power to the circuit.

5. Navodila za uporabo

5.1. Začetna nastavitev: Nastavitev časa in datuma

1. Pritisnite NAČIN button until the time/date setting option appears on the display.
2. Uporabite Puščice gor/dol to adjust the current hour. Press VNESI/NAPREJ za potrditev.
3. Repeat for minutes, AM/PM (if applicable), year, month, and day.
4. Pritisnite NAČIN za izhod iz nastavitvenega menija.

5.2. Programiranje dogodkov VKLOP/IZKLOP

The timer supports multiple ON/OFF events. Refer to the display for available program slots.

1. Pritisnite NAČIN button until 'PROGRAM' or 'EVENT' mode is displayed.
2. Uporabite Puščice gor/dol to select an event number (e.g., 1 ON, 1 OFF). Press VNESI/NAPREJ.
3. Nastavite želeni čas vklopa z uporabo Puščice gor/dol in VNESI/NAPREJ.
4. Set the desired OFF time using the Puščice gor/dol in VNESI/NAPREJ.
5. Select the days of the week for this event to be active (e.g., Mon-Fri, Daily, Weekends). Press VNESI/NAPREJ.
6. Repeat for additional events as needed.
7. Pritisnite NAČIN za izhod iz programiranja.

5.3. Ročni preglas

To temporarily override the programmed schedule:

• Pritisnite eno od tipk VKLOP/IZKLOP buttons to manually switch the output ON or OFF.
• The timer will typically revert to its programmed schedule at the next scheduled event.

5.4. Brisanje pomnilnika

To clear all programmed events or reset the timer:

• Pritisnite in držite POČISTI POMNILNIK button for a few seconds until the display confirms memory clear.
• Lahko pa uporabite tudi PROST VSTOP button to clear individual entries during programming.

6. Vzdrževanje

The Intermatic ET2145CP Electronic Timer requires minimal maintenance. Ensure the unit is kept clean and free from dust and debris. Do not attempt to open the casing or repair the internal components, as there are no user-serviceable parts inside. For cleaning, use a soft, dry cloth. Avoid abrasive cleaners or solvents.

7. Odpravljanje težav

If you encounter issues with your timer, consider the following common troubleshooting steps:

• Brez zaslona/brez napajanja: Check the circuit breaker or fuse supplying power to the timer. Ensure all wiring connections are secure.
• Timer Not Switching: Verify that the programmed events are correctly set and enabled. Check if the manual override is active.
• Napačen čas/datum: Re-enter the correct time and date as per Section 5.1.
• Neenakomerno vedenje: A power surge or interruption might cause erratic behavior. Try resetting the timer by pressing the POČISTI POMNILNIK button (this will erase all programs, requiring re-programming).

If problems persist after attempting these steps, contact Intermatic customer support for assistance.

8. Tehnične specifikacije

9. Garancija in podpora strankam

For information regarding the product warranty, please refer to the warranty card included with your purchase or visit the official Intermatic website. For technical assistance, troubleshooting, or to inquire about replacement parts, please contact Intermatic customer support directly. Contact details can typically be found on the manufacturer's webembalaža spletnega mesta ali izdelka.