SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Uvod

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

Slika 1.1: Spredaj view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Varnostne informacije

• Pred namestitvijo in uporabo natančno preberite vsa navodila.
• Prepričajte se, da je napajalnik voltage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Naprave ne uporabljajte v okoljih s prekomerno vlago, prahom ali korozivnimi plini.
• Pred kakršnim koli vzdrževanjem ali spremembami ožičenja izklopite napajanje.
• Keep the device away from strong electromagnetic interference.

3. Značilnosti izdelka

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Široko območje delovne temperature.
• Compact and easy-to-install design.

4. Vsebina paketa

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x Uporabniški priročnik (ta dokument)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Nastavitev

5.1 Montaža

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Ožičenje

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminala 1 in 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminala 3 in 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminala 6 in 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminali 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminala 11 in 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Navodila za uporabo

6.1 Prikaz končanview

The meter features a dual display:

• PV (vrednost procesa): The upper red display shows the current measured temperature/humidity.
• SV (Nastavljena vrednost): The lower green display shows the desired set point.
• Indikator OUT: Illuminates when the main output is active.
• Indikator AT: Illuminates when the auto-tuning function is active.
• Kazalniki AL1/AL2: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Funkcije gumbov

• Gumb SET: Uporablja se za vstop v način nastavitve parametrov in potrditev izbir.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. V normalnem načinu delovanja pritisnite NASTAVI button once. The SV display will begin to flash.
2. Uporabite ▲ (Gor) in ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Pritisnite NASTAVI button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the NASTAVI button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Gor) in ▼ (Down) buttons to navigate through parameters and the NASTAVI button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Vzdrževanje

• Čiščenje: Obrišite zaslon in casinz mehko, suho krpo. Ne uporabljajte abrazivnih čistil ali topil.
• Pregled: Občasno preverjajte ožičene povezave glede ohlapnosti ali korozije.
• Shranjevanje: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Odpravljanje težav

9. Specifikacije

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Garancija in podpora

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webspletno mesto za kontaktne podatke.