Navodila za uporabo brezžičnega zvonca AVANTEK CW-11

1. Uvod

Thank you for choosing the AVANTEK CW-11 Wireless Doorbell. This manual provides essential information for the proper installation, operation, and maintenance of your new doorbell system. Please read these instructions carefully before use and retain them for future reference.

Image 1.1: AVANTEK CW-11 Wireless Doorbell system, showing the compact transmitter and receiver units.

2. Varnostne informacije

• Naprave ne izpostavljajte ekstremnim temperaturam ali neposredni sončni svetlobi.
• Keep the device away from water and high humidity. The transmitter is IP55 waterproof, but the receiver is for indoor use only.
• Naprave ne poskušajte sami razstaviti ali popraviti. Za pomoč se obrnite na podporo strankam.
• Baterije hranite izven dosega otrok. Rabljene baterije pravilno zavrzite.

3. Vsebina paketa

• 1 x Wireless Transmitter (Doorbell Button)
• 1 x Vtični sprejemnik (zvonček)
• 1 x baterija CR2 (predhodno nameščena v oddajniku)
• 2 x Vijaki
• 2 x sidra
• 1 x dvostranski lepilni trak
• 1 x izvijač

4. Izdelek je končanview

The AVANTEK CW-11 Wireless Doorbell system consists of a battery-powered transmitter (doorbell button) and a plug-in receiver (chime unit). The receiver features 52 selectable melodies, 5 adjustable volume levels, and an LED indicator for visual alerts.

Image 4.1: The receiver unit, illustrating its features including 52 chimes, 5 volume levels, and an LED indicator.

Image 4.2: The compact size of both the transmitter and receiver, designed to not obstruct adjacent power sockets.

5. Navodila za nastavitev

5.1 Installing the Transmitter

The transmitter can be installed using either the provided double-sided adhesive tape or screws and anchor plugs.

Image 5.1: Visual guide for installing the transmitter using either adhesive tape or screws and anchor plugs.

Method A: Using Double-Sided Adhesive Tape

1. Clean the desired mounting surface thoroughly to ensure it is free of dust and moisture.
2. Peel off one side of the protective film from the double-sided adhesive tape and attach it to the back of the transmitter.
3. Peel off the other side of the protective film and firmly press the transmitter onto the cleaned surface for at least 30 seconds.

Method B: Using Screws and Anchor Plugs

1. Mark the desired mounting points for the transmitter on the wall.
2. Na označenih mestih izvrtajte dve luknji.
3. Insert the anchor plugs into the drilled holes.
4. Align the transmitter's mounting holes with the anchor plugs and secure it with the provided screws.

Pomembno: To prevent signal interference, do not install the transmitter close to or on metal surfaces such as metal door frames or mailboxes.

5.2 Plugging in the Receiver

Plug the receiver into a standard electrical outlet in a location where the chime can be easily heard. The LED on the receiver will flash upon initial power-up.

5.3 Pairing the Doorbell System

The transmitter and receiver are pre-paired at the factory. If re-pairing is needed or if you add additional transmitters/receivers, follow these steps:

1. Priključite sprejemnik v električno vtičnico.
2. To enter pairing mode, hold down the Volume button on the receiver for 3 seconds. The LED on the receiver will flash.
3. Remove the battery insulating film from the transmitter (if not already done).
4. Press the Push button on the transmitter. Its LED will flash.
5. After successful pairing, the receiver will chime once, and the LEDs on both the receiver and transmitter will flash simultaneously.

6. Navodila za uporabo

6.1 Spreminjanje melodij

The receiver offers 52 different melodies. Use the 'Next' and 'Previous' buttons on the side of the receiver to cycle through the available tunes. Press the doorbell button to preview the selected melody.

Image 6.1: The receiver offers a wide selection of melodies for personalization.

6.2 Prilagajanje glasnosti

There are 5 adjustable volume levels, with a maximum setting of 115 dB. Use the 'Volume' button on the side of the receiver to increase or decrease the sound level.

6.3 Način izklopa zvoka

To activate mute mode (0 dB), repeatedly press the 'Volume' button until the sound is off. In this mode, only the LED indicator will flash when the doorbell is pressed, providing a silent visual alert.

Image 6.2: The mute mode feature allows for silent notifications, ideal for quiet environments.

7. Vzdrževanje

7.1 Čiščenje

Wipe the devices with a soft, dry cloth. Do not use abrasive cleaners or solvents.

7.2 Battery Replacement (Transmitter)

The transmitter uses a CR2 battery with an estimated lifespan of 3 years. When the battery is low, the transmitter's LED may not light up or the signal range may decrease. To replace the battery:

1. Previdno odprite oddajnik casinz uporabo priloženega izvijača ali majhnega ploščatega izvijača.
2. Odstranite staro baterijo CR2.
3. Vstavite novo baterijo CR2 in pri tem pazite na pravilno polarnost (+/-).
4. Zaprite casing varno.

8. Odpravljanje težav

• Zvonec ne zvoni: Ensure the receiver is plugged in and powered. Check the transmitter battery. Re-pair the devices if necessary (refer to Section 5.3).
• Short signal range: Ensure the transmitter is not installed on or near metal surfaces. Relocate the receiver to a more central position. Replace the transmitter battery.
• Motnje: The doorbell operates on a frequency that minimizes interference with other household devices. If interference occurs, try changing the melody or relocating the receiver.
• Funkcija pomnilnika: The device remembers your last melody and volume level after a power outage, so no need to reset settings.

9. Specifikacije

10. Garancija in podpora

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official AVANTEK webspletno mesto. Shranite račun kot dokazilo o nakupu.