1. Uvod
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your RANDOM Snappy Round Bottle Trap. Designed for basin sinks, this ABS plastic P-trap kit ensures efficient waste drainage and a clean aesthetic. Please read this manual thoroughly before beginning installation to ensure proper function and longevity of the product.
2. Varnostne informacije
Always prioritize safety during installation and maintenance. Follow these general guidelines:
- Turn off the main water supply to the sink before starting any work.
- Nosite ustrezno osebno zaščitno opremo, kot so rokavice in zaščita za oči.
- Prepričajte se, da so vse povezave varne in vodotesne, da preprečite puščanje.
- Če ste glede katerega koli koraka negotovi, se posvetujte z usposobljenim vodovodarjem.
3. Vsebina paketa
Pred začetkom namestitve preverite, ali so prisotne vse komponente:
- 1x Bottle P-Trap Body
- 1x prirobnica
- 1x Tail Pipe
- Gaskets and Washers (various sizes)
- 1x Drain Cap (if included with specific drain assembly)
- 1x Brass Locking Nut (if included with specific drain assembly)
4. Specifikacije
| Funkcija | Podrobnost |
|---|---|
| Znamka | NAKLJUČNO |
| Številka modela | RD83880 |
| Material | Akrilonitril butadien stiren (ABS) |
| barva | Bela |
| Zunanji premer | 1.25 palcev |
| Združljivost | Works with any 1-1/4 inch Drain Assembly; suitable for Undermount, Vessel, and Pedestal Sinks. |
| Največji tlak | 1 MPa (at room temperature 20°C) |
5. Vodič za namestitev
This section provides step-by-step instructions for installing your RANDOM Snappy Round Bottle Trap. For a visual guide, please refer to the installation video below.
5.1. Koraki pred namestitvijo
- Razpakirajte in preglejte: Carefully remove all components from the packaging. Inspect them for any damage or missing parts.
- Disassemble Drain Assembly (if applicable): If your sink drain assembly is new, separate its components as shown in the video (Drain cap, Silicon Gasket, Plastic Washer, Tail Pipe, Brass Locking Nut).
5.2. Assembling the Bottle Trap
- Assemble Bottle Trap Body: Attach the tail pipe to the main bottle trap body, ensuring the necessary seals and washers are correctly positioned and tightened. The video demonstrates how to connect the pipe to the bottle trap body, securing it with the appropriate seals.
- Prepare Sink Drain: Ensure the sink drain assembly (pop-up drain or standard drain) is properly installed in the sink basin, with all seals and nuts tightened from underneath the sink.
5.3. Connecting the Bottle Trap to the Sink and Wall
- Connect to Sink Drain: Align the top of the assembled bottle trap with the tail pipe of the sink drain assembly. Connect them, ensuring the proper washer is in place for a watertight seal. Tighten the nut securely by hand, then use a wrench for a final snug turn, being careful not to overtighten.
- Priključitev na odtok v steni: Aim the horizontal outlet of the bottle trap at the hole of the drainage wall. Adjust the distance between the drain and the wall as needed. Insert the pipe into the wall drain opening.
- Varna stenska povezava: Connect the water inlet of the bottle trap to the water outlet of the wall drain. Ensure all connections are tight and secure.
5.4. Preverjanje po namestitvi
- Test za puščanje: Turn on the water supply to the sink. Fill the sink with water and then drain it, observing all connections for any signs of leaks. Repeat this process several times.
- Prilagodite, če je potrebno: If any leaks are detected, gently tighten the corresponding nuts. Do not overtighten, as this can damage the seals or plastic components.
6. Delovanje in vzdrževanje
The RANDOM Snappy Round Bottle Trap is designed for low maintenance. Regular checks and simple cleaning can ensure its long-term performance.
6.1. Redno čiščenje
Periodically, you may need to clean the bottle trap to remove accumulated debris or hair. This is a key advantage of a bottle trap design.
- Place a bucket or container directly underneath the bottle trap to catch any water or debris.
- Unscrew the bottom cap of the bottle trap body (refer to Figure 5.4).
- Allow water and debris to drain into the bucket.
- Clean the inside of the trap and the cap thoroughly with a brush or cloth.
- Replace the cap, ensuring the O-ring is properly seated for a watertight seal. Tighten securely.
6.2. Leak Checks
It is advisable to periodically check for leaks, especially after any maintenance or if you notice reduced drainage speed.
- Visually inspect all connections for drips or moisture.
- Run water through the sink and observe the trap for any signs of leakage.
- If leaks are found, gently tighten the connections. Avoid excessive force.
7. Odpravljanje težav
Tukaj je nekaj pogostih težav in njihovih možnih rešitev:
| Težava | Možen vzrok | rešitev |
|---|---|---|
| Puščanja na priključkih | Loose nuts, improperly seated gaskets/washers, damaged seals. | Ensure nuts are tightened securely (hand-tight plus a quarter turn with a wrench). Check that all gaskets and washers are correctly positioned and not damaged. Replace damaged seals if necessary. |
| Slow drainage or clog | Accumulation of hair, soap scum, or debris in the trap. | Follow the "Regular Cleaning" steps (Section 6.1) to clear the trap. |
| Trap not aligning with wall drain | Incorrect measurement or positioning during installation. | The bottle trap design requires precise alignment. Re-evaluate the distance and angle between the sink drain and the wall drain. Adjust the tail pipe length if possible, or consider professional assistance. |
8. Garancija in podpora
The RANDOM Snappy Round Bottle Trap comes with a 5-letna garancija kakovosti. We are committed to providing high-quality products and excellent customer service.
For any questions, concerns, or support needs, please contact Kaiping City Langdeng Plumbing Industry Co.,Ltd, the manufacturer backing this product. You can also visit the official RANDOM store on Amazon for more information and products: RANDOM Store.
