BEMKO B62-TSMD20 TS SCHUKO Plug-in Timer User Manual

1. Uvod

This manual provides detailed instructions for the safe and efficient use of your BEMKO B62-TSMD20 TS SCHUKO Plug-in Timer. Please read this manual thoroughly before installation and operation to ensure proper function and to prevent damage or injury. This device is designed to automatically switch electrical appliances ON and OFF at pre-set times over a 24-hour period.

2. Varnostne informacije

• Always disconnect power before attempting any installation, maintenance, or cleaning.
• Do not exceed the maximum load rating of 3500W or 16A. Overloading can cause damage to the device and connected appliances, and may pose a fire hazard.
• Ensure the timer is plugged into a properly grounded 230V/50Hz electrical outlet.
• This device is designed for indoor use only. Do not expose it to water, moisture, or extreme temperatures.
• Ne poskušajte odpirati ali popravljati naprave. Vsa servisna dela prepustite usposobljenemu osebju.
• Hraniti izven dosega otrok.

3. Izdelek je končanview

The BEMKO B62-TSMD20 is an analog plug-in timer designed for simple and reliable control of electrical devices. It features a 24-hour dial for setting daily programs and a manual override switch.

Slika 1: Spredaj view of the BEMKO B62-TSMD20 TS SCHUKO Plug-in Timer. The image displays the timer with a central Schuko type electrical socket. This socket is surrounded by a rotating 24-hour dial marked with numbers from 1 to 24 (or AM/PM indications) and small, push-down pins along its circumference for setting time intervals. A manual override switch is visible on the right side of the white casing.

Ključne komponente:

• Schuko Socket: For plugging in the appliance to be controlled.
• 24-urni prikaz: Rotates clockwise, marked with hours and minutes.
• Programski zatiči: Small segments around the dial, each representing 15 minutes.
• Ročno preglasitveno stikalo: Allows for continuous ON, continuous OFF, or timer-controlled operation.

4. Nastavitev

1. Plug In: Insert the BEMKO B62-TSMD20 timer into a standard 230V/50Hz wall outlet.
2. Nastavi trenutni čas: Rotate the 24-hour dial clockwise until the current time aligns with the arrow or marker on the timer's body. Ensure you distinguish between AM and PM hours (e.g., 3 PM is 15:00).
3. Nastavite program:
   • Each segment (pin) on the dial represents 15 minutes.
   • To set an 'ON' period, push the corresponding pins downwards.
   • To set an 'OFF' period, leave the corresponding pins in the upward position.
   • Na primerample, to turn an appliance ON from 7:00 AM to 8:00 AM, push down all four pins between the 7 and 8 o'clock marks.
4. Priključite napravo: Plug the appliance you wish to control into the Schuko socket on the front of the timer.

5. Navodila za uporabo

Ročno preglasitveno stikalo:

The manual override switch, typically located on the side of the timer, allows you to control the power output independently of the set program. It usually has three positions:

• Timer Mode (Clock Icon): The timer operates according to the set program (pins pushed down/up).
• Always ON (I Icon): The power output is continuously ON, regardless of the program settings.
• Always OFF (O Icon): The power output is continuously OFF, regardless of the program settings.

Select the desired mode by sliding the switch to the appropriate position.

6. Vzdrževanje

• Čiščenje: Disconnect the timer from the power outlet before cleaning. Wipe the exterior with a soft, dry cloth. Do not use liquid cleaners, abrasives, or solvents.
• Shranjevanje: Ko časovnika ne uporabljate, ga hranite na hladnem in suhem mestu.
• The BEMKO B62-TSMD20 contains no user-serviceable parts. Do not attempt to disassemble the unit.

7. Odpravljanje težav

• Appliance not turning ON/OFF:
  • Check if the timer is securely plugged into the wall outlet.
  • Verify that the appliance is correctly plugged into the timer's socket.
  • Ensure the manual override switch is set to the 'Timer Mode' (clock icon).
  • Confirm that the program pins are correctly set for the desired ON/OFF times.
  • Check if the current time on the dial is accurately set.
• Timer not advancing:
  • Ensure the timer is receiving power from the wall outlet.
  • If the timer has been unplugged for an extended period, it may need to be reset to the current time once power is restored.
• Pregrevanje:
  • Immediately unplug the timer and the connected appliance.
  • Ensure the connected appliance's power consumption does not exceed the timer's maximum load rating (3500W / 16A).

8. Specifikacije

9. Garancija in podpora

For warranty information, technical support, or service inquiries regarding your BEMKO B62-TSMD20 TS SCHUKO Plug-in Timer, please contact your retailer or the manufacturer, Bemko, directly. Please retain your proof of purchase for warranty claims.