Uvod
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Varnostne informacije
- Optičnega bralnika ne izpostavljajte ekstremnim temperaturam, vlagi ali neposredni sončni svetlobi.
- Pazite, da vam skener ne pade ali da ga ne izpostavljate močnim udarcem.
- Ne poskušajte odpirati ali spreminjati optičnega bralnika. Vsa servisna dela prepustite usposobljenemu osebju.
- Use only the power supply and cables provided or approved by Intermec.
- Keep the scanning window clean to ensure accurate barcode reading.
Vsebina paketa
Preverite, ali vaš paket vsebuje naslednje elemente:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Napajalna enota
- Dokumentacija (ta priročnik ali podobno)
Če kateri koli predmet manjka ali je poškodovan, se nemudoma obrnite na svojega dobavitelja.
Nastavitev
1. Priključitev skenerja
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Povežite se s skenerjem: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Priključite napajalnik: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Začetni vklop
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Upravljanje skenerja
1. Skeniranje črtnih kod
- Cilj: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- skeniranje: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Potrditev: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Razumevanje kazalnikov
- Zelena LED: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Vzdrževanje
Čiščenje optičnega bralnika
- Redno čistite okno za skeniranje z mehko krpo, ki ne pušča vlaken.ampz vodo ali blagim, neabrazivnim čistilom.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Ensure the scanner is powered off before cleaning.
Shranjevanje
Ko skenerja ne uporabljate, ga shranjujte v čistem in suhem okolju, stran od neposredne sončne svetlobe in ekstremnih temperatur.
Odpravljanje težav
| Težava | Možen vzrok | rešitev |
|---|---|---|
| Skener se ne vklopi. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Skener ne bere črtnih kod. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Specifikacije
- Model: SR30
- Številka dela: 225-727-003 (Kit)
- Vrsta optičnega bralnika: Linearni slikovnik
- Vmesnik: RS232
- Proizvajalec: Intermec
- Teža artikla: 0.01 ounces (approximate, scanner only)
- Oddelek: Črtna koda
- ASIN: B003T0WF3S
Garancija in podpora
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webspletnega mesta. Račun shranite kot dokazilo o nakupu za uveljavljanje garancije.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
