SpeedyBee F405 V5 Stack BLS 55A 4-in-1 ESC & FC Instruction Manual

1. Uvod

This manual provides detailed instructions for the installation, configuration, and operation of your SpeedyBee F405 V5 Flight Controller (FC) and BLS 55A 4-in-1 Electronic Speed Controller (ESC) stack. This high-performance stack is designed for FPV drones, offering advanced features and robust performance. Please read this manual thoroughly before use to ensure proper setup and safe operation.

2. Varnostne informacije

⚠️ Samo za rekreativno uporabo. Nezakonito spreminjanje dronov/letal je prepovedano. Za zagotovitev zakonite uporabe bodite pozorni tudi na ustrezne zakone in predpise o uporabi dronov/letal v vaši državi/območju.

Always ensure correct polarity when connecting power. Incorrect wiring can cause severe damage to the components.
Exercise caution when soldering. Use appropriate safety gear and ensure proper ventilation.
Keep the stack away from moisture and extreme temperatures.
Disconnect the battery before performing any maintenance or modifications.
Ensure all connections are secure before powering on your drone.

3. Vsebina paketa

The SpeedyBee F405 V5 Stack BLS 55A is available in different configurations. Please verify your package contents against the list below.

Standardna vsebina paketa

SpeedyBee F405 V5 Stack Standard Package Contents — Standard Package Contents for SpeedyBee F405 V5 Stack.

Krmilnik leta za modele letal SpeedyBee F405 V5 x1
SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
6-pinski priključni kabel GPS + 6-pinski priključek SH1.0 x1 (SH1.0 6-pinski * 120 mm)
4-pinski priključni kabel GPS + 4-pinski priključek SH1.0 x1 (SH1.0 6-pinski na SH1.0 4-pinski *120 mm)
4-pinski priključni kabel sprejemnika x1 (SH1.0 4-pinski * 100 mm)
Napajalni kabel XT60 x1 (120 mm)
Vijaki za pritrditev sklada modelov letal M3 x4 (30 mm)
Šesterokotne najlonske matice M3 x5
M3 črne silikonske podložke x5
Termoskrčljiva cev za kondenzatorje x2
Silikonski ovitki za modelna letala FC x 5
Silikonski pokrovi za ESC modelnih letal x 5
35V 1000uF trdni kondenzator x1
Hitri vodnik za model letalskega sklada x1

Deluxe Package Contents

Krmilnik leta za modele letal SpeedyBee F405 V5 x1
SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
Tabla za vadbo spajkanja x1
Orodje za zaščito pred kratkim stikom x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm) x1
Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm) x1
DJI Air Unit Connector Cable (SH1.0 6pin*80mm) x1
6-pinski priključni kabel GPS + 6-pinski priključek SH1.0 x1 (SH1.0 6-pinski * 120 mm)
4-pinski priključni kabel GPS + 4-pinski priključek SH1.0 x1 (SH1.0 6-pinski na SH1.0 4-pinski *120 mm)
4-pinski priključni kabel sprejemnika x1 (SH1.0 4-pinski * 100 mm)
Rdeča in črna žica za brenčalo x1 (100 mm)
Aktivni brenčalo x1
1x 4-pinski priključni kabel za razširitveni modul tipa C (SH1.0 4-pinski * 80 mm)
Razširitveni modul tipa C x1
Šesterokotne najlonske matice M3 x5
M3 črne silikonske podložke x5
Silikonski ovitki za modelna letala FC x 5
Silikonski pokrovi za ESC modelnih letal x 5
Pritrdilni vijaki M3 x 4 (30 mm)
Razširitvena plošča za napajanje x4
Termoskrčljiva cev za kondenzatorje x2
35V 1000uF trdni kondenzator x1
Hitri vodnik za model letalskega sklada x1

4. Izdelek je končanview

Krmilnik letenja SpeedyBee F405 V5

SpeedyBee F405 V5 Flight Controller Top View — Vrh view of the SpeedyBee F405 V5 Flight Controller.

SpeedyBee F405 V5 Flight Controller Layout — Detailed layout of the F405 V5 Flight Controller, showing component labels and connections.

The F405 V5 Flight Controller features an STM32F405 MCU and an ICM42688P Gyro for precise flight control. It includes a built-in barometer (SPA06-003) for accurate altitude readings and an AT7456E OSD chip for on-screen display. Connectivity includes a new Type-C USB port and full-featured Bluetooth tuning via the SpeedyBee App, allowing for wireless firmware flashing and parameter tuning. It supports 6-pin direct plug-in or solder connection for DJI Air Units and has a built-in 16MB Blackbox storage chip for flight data logging.

Power outputs include 9 groups of 5V output (total 1.5A), 2 groups of 9V output (total 3A) with PINIO remote on/off control, 1 group of 3.3V output, and 3 groups of 4.5V output (max 1A) for peripherals like receivers and GPS modules. It supports 8 motor outputs (M1-M4 on bottom, M5-M8 on front) and multiple UARTs for various peripherals.

SpeedyBee BLS 55A 4-v-1 ESC

SpeedyBee BLS 55A 4-in-1 ESC Top View — Vrh view of the SpeedyBee BLS 55A 4-in-1 ESC.

SpeedyBee BLS 55A 4-in-1 ESC Layout — Detailed layout of the BLS 55A 4-in-1 ESC, showing internal components and connections.

The BLS 55A 4-in-1 ESC is designed for 3-6S LiPo input, providing a continuous current of 55A per channel (220A total) and a burst current of 70A (280A total) for 10 seconds. It features a built-in TVS protective diode for surge protection and includes a 1000uF Low ESR Capacitor in the package for enhanced stability. The ESC supports DSHOT300/600 protocols and current sensing (Scale=400, Offset=0). It also supports ESC Telemetry.

ESC Protection Features — The ESC includes a TVS Protective Diode, 21 onboard TDK capacitors, and supports an external 1000uF high-capacity electrolytic capacitor for upgraded protection against voltage spikes and interference.

5. Namestitev

Montaža

The SpeedyBee F405 V5 FC and BLS 55A ESC both feature 30.5 x 30.5mm mounting holes with a 4mm hole diameter. They are designed to be stacked together using the provided silicone grommets and screws.

FC and ESC Installation Methods — Diagram illustrating soldering, direct plug, standard, and reverse installation methods for the FC and ESC. When fixing the stack, use M3 black silicone washers to ensure sufficient space between the flight controller and the ESC.

Connecting the FC and ESC

The FC and ESC can be connected via a 10-pin connector or by direct soldering. The 10-pin design provides enhanced safety redundancy.

FC and ESC Connection with Motors — Connection diagram for the FC and ESC with motors, including the 1000uF Solid Capacitor and XT60 Power Cable. It is strongly recommended to use the included 1000uF solid capacitor to protect the AIO flight controller from instantaneous voltagkonice, ko je vklopljen.

6. Sheme ožičenja

Comprehensive Wiring Diagram

Priključek zračne enote DJI

DJI Air Unit Connection Diagrams — Diagrams for connecting the FC to DJI O3 Air Unit, RunCam Link/Caddx Vista Air Unit, and DJI Air Unit V1 using the 6-pin cable.

Receiver Specific Notices

SBUS Receiver Importance Notice — Importance notice for SBUS receiver: When using an SBUS receiver, the SBUS signal wire must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If also using a DJI Air Unit (O3/Link/Vista/Air Unit V1), you must disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. Use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

ELRS Receiver Importance Notice — Importance notice for ELRS receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

7. Konfiguracija

Wireless Tuning via SpeedyBee App

Configure FC and ESC via Bluetooth — The SpeedyBee app allows you to configure your FC and ESC via Bluetooth, enabling wireless tuning and firmware updates.

The SpeedyBee F405 V5 FC supports full-featured Bluetooth tuning. Connect to the SpeedyBee App on your smartphone to flash FC firmware, tune parameters, and configure your quad anytime, anywhere. Ensure MSP is enabled with Baud rate 115200 on UART4 for Bluetooth connection.

Sprememba smeri motorja

You can change motor directions wirelessly using the SpeedyBee app. Connect to the app, navigate to 'Motors' and then 'Motor Direction Settings' to adjust as needed.

Nadzor LED traku

LED Pads with Simple Switching — Diagram showing the FC with four sets of LED pads, allowing for simple switching of LED presets. LED strips could be purchased separately. Long press the boot button to switch to Betaflight LED mode.

The FC supports 4 sets of LED pads. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. Short-press the BOOT button to cycle through different LED displaying modes. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.

8. Navodila za uporabo

Once installed and configured, your SpeedyBee F405 V5 Stack is ready for flight. Ensure your radio transmitter is properly bound and configured with your receiver. Always perform pre-flight checks, including propeller security, battery level, and control surface response, before each flight.

Vklop: Connect your LiPo battery to the XT60 connector. The FC and ESC will initialize.
Oborožitev: Arm your drone using your configured arming switch on your radio transmitter.
Let: Operate your drone according to standard FPV flight practices.
Razorožitev: Disarm your drone using your configured disarming switch after landing.

9. Odpravljanje težav

Flight Controller Not Responding / Bricked

If your FC becomes unresponsive or appears 'bricked', you can force it into DFU (Device Firmware Upgrade) mode for firmware flashing:

Press and hold the BOOT button on the FC.
While holding the BOOT button, connect the FC to your computer via the USB Type-C cable.
The FC should now be in DFU mode, allowing you to flash new firmware using Betaflight Configurator.

SD Card Compatibility Issues

SD Card Compatibility Information — Information regarding SD card compatibility for the F405 V5 Flight Controller. The F405 V5 FC supports Standard (SDSC) or High Capacity (SDHC) microSD cards under 32GB. Extended capacity cards (SDXC) are not supported. Cards must be formatted with FAT16 or FAT32. Betaflight can only recognize a maximum of 4GB.

Betaflight firmware requires the microSD card to be either Standard (SDSC) or High Capacity (SDHC) and under 32GB. Extended Capacity cards (SDXC) are not supported. The microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format. While you can use any SD card less than 32GB, Betaflight can only recognize a maximum of 4GB. It is recommended to use a 3rd party formatting tool and choose 'Overwrite format' when formatting your card.

10. Specifikacije

SpeedyBee F405 V5 30.5×30.5mm Model Aircraft Flight Controller

Funkcija	Specifikacija
MCU	STM32F405
IMU (žiroskop)	ICM42688P
Vrsta vrat USB	Nov vmesnik tipa C
Barometer	SPA06-003
OSD čip	AT7456E
Polno opremljeno uglaševanje Bluetooth	Podprto. Povežite se prek aplikacije SpeedyBee za posodobitev vdelane programske opreme FC in nastavitev parametrov.
Nadgradnja vdelane programske opreme brezžičnega FC	Podprto
Priključek zračne enote DJI	Podpira 6-pinski neposredni vtič ali spajkalno povezavo
Blackbox	Podprt, vgrajen 16MB pomnilniški čip
Vhodna voltage	3-6S LiPo baterija
Neodvisen 5V BEC izhod	9 skupin (4× +5V kontakti spredaj, 1× BZ+ kontakt za brenčalo in 4× +5V kontakti na vogalih za zunanje LED diode). Skupni izhodni tok: 1.5 A.
Neodvisen 9V BEC izhod	2 skupini (1x 9V kontakt spredaj, 1x 9V izhod v priključku zadaj). Skupni izhodni tok: 3A. Podpira daljinski vklop/izklop PINIO.
Napajanje mikrokontrolerja in žiroskopa	Neodvisni LDO
3.3V izhod	1 skupina (1× 3.3V blazinica spredaj)
4.5V izhod	3 skupine (3× 4.5 V kontaktne blazinice spredaj). Lahko napaja sprejemnik in GPS, ko je FC napajan prek USB-ja. Največji izhodni tok: 1 A.
ESC signal	Priključne ploščice M1-M4 in 10-pinski konektor na zadnji strani
Servo signal	Sprednje blazinice S5-S6
Vhod za telemetrijo ESC	Podprto (UART5)
Podloga za nastavitev kamere Betaflight	Podprto (CC blazinica spredaj)
I2C	Podprto (GPS priključek + blazinice)
UART	UART1 (Bluetooth); UART2 (sprednje ploščice za sprejemnik); UART3 (ploščice DJI VTX + zadnji SH1.0-6-pinski); UART4 (ploščice GPS + sprednji SH1.0-6-pinski); UART5 (TLM); UART6 (ploščice sprejemnika + zadnji SH1.0-4-pinski)
ST LED blazinice	Podprto, na sprednjih G/5V/LED ploščicah; krmiljeno s programsko opremo FC
LED trakovi Meteor	Podprto. Preklapljanje med načinoma SB-LED in ST-LED prek gumba BOOT ali aplikacije. V načinu SB-LED ga upravlja Bluetooth čip ESP32.
Brenčala	Podprto
Gumb BOOT	[A] Med vklopom držite tipko BOOT, da prisilite utripanje v način DFU. [B] Ko je vklopljen in v stanju pripravljenosti, s kratkim pritiskom preklapljate med načini prikaza LED; z dolgim pritiskom stikala SB-LED/ST-LED. V načinu ST-LED so LED1–LED4 krmiljene s programsko opremo FC.
RSSI blazinice	Podprto
SmartPort	Ni podprto
Podprta vdelana programska oprema FC	Betaflight, INAV, Ardupilot
Ciljno ime vdelane programske opreme	SPEEDYBEEF405V5
Tovarniška različica vdelane programske opreme	Betaflight 4.5.2
Različica konfiguratorja	Betaflight 10.10.0
Montažne luknje	30.5 × 30.5 mm (Ø4 mm), stranska odprtina
Dimenzije	39 mm (D) × 39 mm (Š) × 4.9 mm (V)
Teža	8.1 g

SpeedyBee OX32 55A 30.5 × 30.5 4-v-1 ESC

Funkcija	Specifikacija
Privzeta vdelana programska oprema	OX32
Neprekinjeni tok	55 A (na kanal) / 220 A (4 v 1)
Največji tok	70 A (na kanal) / 280 A (4 v 1)
Zaščitna dioda TVS	Da (vgrajeno)
Zunanji kondenzator	1000µF trdni kondenzator (vključen v paketu)
Protokol ESC/motor	DSHOT300/600
Vhodna voltage	3-6S LiPo
Izhodna moč	VBAT
Trenutni senzor	Podprto
ESC telemetrija	Podprto
Montažne luknje	30.5 × 30.5 mm (Ø4 mm), stranska odprtina
Dimenzije	40.9 mm (D) × 44.9 mm (Š) × 8.0 mm (V) (vključno s hladilnikom)
Teža	19.1 g
Opomba o merilniku toka	Podprto (Lestvica=27, Odmik=-2644)

SpeedyBee F405 V5 Stack Dimensions — Dimensions of the assembled SpeedyBee F405 V5 Stack.

11. Uporabniški nasveti

Brezžično udobje: Vzemite polni napredektage of the SpeedyBee app's wireless tuning capabilities. This eliminates the need for a laptop in the field for minor adjustments or quick checks.
Kondenzator je ključnega pomena: Always install the included low ESR capacitor. It's crucial for protecting your flight controller from voltage spikes, especially during aggressive maneuvers or power-intensive operations.
Formatiranje kartice SD: If you experience issues with Blackbox logging, double-check your microSD card's format (FAT16/FAT32) and ensure it's an SDSC or SDHC type under 32GB. Reformatting with an 'Overwrite format' option can often resolve problems.
Ožičenje sprejemnika: Pay close attention to the specific wiring instructions for SBUS and ELRS receivers, especially when integrating with DJI Air Units, to avoid recognition issues.

12. Garancija in podpora

For warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. Always refer to the official SpeedyBee website for the latest firmware updates and support resources.

	Uporabniški priročnik za SpeedyBee F405 V4 BLS 55A 30x30 Stack V1.0 Obsežen uporabniški priročnik za SpeedyBee F405 V4 BLS 55A 30x30 Stack, ki podrobno opisuje njegove specifikacije, fizične dimenzije, vsebino paketa, načine povezave FC in ESC, periferne povezave, konfiguracijo aplikacij in vdelane programske opreme ter postopke posodabljanja vdelane programske opreme.
	SpeedyBee F405 V3 60A sklad: Priročnik za krmilnik leta in ESC Celovit vodnik za krmilnik leta SpeedyBee F405 V3 in sklad 4-v-1 ESC BLS 60A, ki zajema specifikacije, namestitev, povezave, posodobitve vdelane programske opreme in nastavitev parametrov.
	SpeedyBee F405 AIO User Manual: Setup, Connections, and Firmware Guide Explore the SpeedyBee F405 AIO flight controller with this comprehensive user manual. Covers specifications, wiring diagrams, firmware flashing, and setup for FPV drones.
	SpeedyBee F405 AIO Flight Controller User Manual Comprehensive user manual for the SpeedyBee F405 AIO flight controller, covering specifications, peripheral connections, installation, firmware flashing, and ESC configuration.
	Uporabniški priročnik za SpeedyBee F405 V3 BLS 50A 30x30 Stack V1.0 Obsežen uporabniški priročnik za SpeedyBee F405 V3 BLS 50A 30x30 Stack, ki podrobno opisuje specifikacije, postavitev, povezave, konfiguracijo in posodobitve vdelane programske opreme za krmilnik leta in 4-v-1 ESC.
	Uporabniški priročnik za SpeedyBee F405 V4 BLS 60A 30x30 Stack Uporabniški priročnik za krmilnik leta SpeedyBee F405 V4 in sklad 4-v-1 ESC BLS 60A. Zajema specifikacije, povezave, konfiguracijo aplikacije in računalnika ter posodobitve vdelane programske opreme za FPV drone.