1. Uvod
This manual provides essential information for the safe and effective use of your Japan Nidec 24H Brushless Servo Motor. This motor features a built-in drive and 100-line dual-channel encoder, making it suitable for high-precision control applications. Please read this manual thoroughly before operation.
2. Varnost in opozorila
- Do not operate the motor under overload (stall) conditions, as this may easily damage the motor.
- Select a power supply with appropriate voltage (DC).
- If the load exceeds the rated value, the rotational speed will decrease.
- Operating near the stall torque limit may cause internal damage.
- Reducing the rotational speed will result in decreased output torque.
- It is strictly forbidden to make mistakes regarding the positive and negative connections of the brushless motor.
- Always use a regulated, non-surge DC power supply (e.g., a battery or regulated power supply).
Opozorilo o nevarnosti zadušitve
This product may contain small parts. Keep out of reach of children under 3 years to prevent choking hazards.
3. Izdelek je končanview
The Nidec 24H Brushless Servo Motor is a compact and powerful motor designed for precision applications. It features an integrated brushless driver and a 100-line encoder for accurate feedback and control.
4. Specifikacije
Splošne lastnosti
- Tip: Mikro motor
- Commutation: Brez krtačk
- Izvor: celinska Kitajska
- Certificiranje: CCC
- Pogoj: Used (dismantled, tested and in perfect working order)
Električni podatki
| voltage | Brez toka | Hitrost brez obremenitve |
|---|---|---|
| DC 9V | 70mA | 2246 RPM |
| DC 12V | 80mA | 3020 RPM |
| DC 24V | 100mA | 6100 RPM |
Dimenzije
Informacije o paketu
- Teža: 0.15 kg
- Dimenzije (D x Š x V): 9 cm x 9 cm x 9 cm
5. Nastavitev
Navodila za ožičenje
Refer to the wiring diagram below for proper connections. Ensure all connections are secure before applying power.
- Rdeča žica: Napajalnik pozitiven
- Črna žica: Napajanje negativno
- rumena žica: Start/Stop (Connect to positive power supply via a 1k resistor; below 12V, no resistor needed)
- White Wire (PWM): PWM signal speed control (Connect to negative for high speed; input 20KHz pulse width signal for speed regulation)
- zelena žica: Forward-reverse switching (Connect to negative to switch direction)
- Brown Wires (Signal A, Signal B): Signali kodirnika
- Oranžna žica: Encoder power supply 5V
Montaža
The motor bracket can be removed if necessary for custom mounting solutions.
6. Navodila za uporabo
Osnovno delovanje
- Connect the red wire to the positive pole and the black wire to the negative pole of your DC power supply.
- Connect the yellow 'Start' line to the positive power supply via a 1k resistor. If operating below 12V, a resistor is not required.
- To run at high speed, connect the white PWM line directly to the negative pole.
- For speed regulation, input a 20KHz pulse width modulation (PWM) signal to the white line.
- To switch between forward and reverse rotation, connect the green line to the negative pole. It is recommended to stop the motor before switching direction to prevent instantaneous surges.
- The encoder requires a 5V power supply connected to the orange wire. If the encoder is not needed, this connection can be ignored.
7. Vzdrževanje
This brushless servo motor is designed for low maintenance. Keep the motor clean and free from dust and debris. Ensure proper ventilation to prevent overheating. No specific user-serviceable parts are inside.
8. Odpravljanje težav
- Motor not starting or erratic operation: Check all wiring connections for correctness, especially positive/negative polarity. Ensure the power supply is regulated and within the specified voltagobmočje e (9 V–24 V enosmernega toka).
- Pregrevanje motorja: Reduce the load on the motor. Ensure it is not operating under stall conditions. Verify that the power supply voltage is correct and not exceeding 24V.
- Reduced speed or torque: The load might be exceeding the motor's rated value. Reduce the load or ensure the motor is not operating near its stall torque limit.
- No encoder feedback: Ensure the encoder's 5V power supply (orange wire) is correctly connected.
9. Uporabniški nasveti
- Kabli: This motor is typically sold without connecting cables. You will need to source appropriate wires and connectors for your application.
- Dimenzije gredi: For precise integration, carefully measure the helical portion of the shaft if specific dimensions are critical for your project. The shaft diameter is 6mm and length is 18.5mm.
- Pogoj: As these motors are often used and dismantled, minor cosmetic imperfections like oxidation or rust spots may be present, but they are tested for perfect working order.
10. Garancija in podpora
For detailed information regarding the manufacturer and EU representative, please refer to the original user manual PDF.
Proizvajalec: Dongguan Haodarong Trading Co., Ltd
Naslov: Room406, No.11, Jiaoyu Road, Dongcheng Street, Dongguan, China
Kontaktna oseba: Liao Jiansheng
E-pošta: mox0903@163.com
Odgovorna oseba EU: QTEC EUREP GMBH
Naslov: CURTIUSSTRASSE 27, 23568 LUEBECK, Germany
E-pošta: Cpcs@cpcs-tlab.hk
telefon: +852-53700017
Obsežen uporabniški priročnik v formatu PDF je na voljo za prenos: View Uporabniški priročnik (PDF)
