LCD-zaslon na dotik lcdwiki E32R40T
Specifikacije
- Product Name: LCDWIKI 4.0inch ESP32-32E E32R40T&E32N40T
- Zaslonski modul: 4.0-palčni ESP32-32E
- Številka modela: CR2025-MI3275
- Webspletno mesto: www.lcdwiki.com
Vklopite izdelek
Za povezavo računalnika z izdelkom in napajanje izdelka uporabite kabel tipa C z napajalnikom in funkcijo prenosa podatkov. Kot je prikazano na spodnji sliki:
Namestite gonilnik za vrata USB v serijska vrata
- Locate the USB-SERIAL_CH340.zip package in the “7-工具软件_Tool_software” folder and decompress it.
- go to the folder after decompression, double-click “CH341SER.EXE” executable program, pop up the installation window, and then click “Install” button to continue the installation, as shown in the following picture:
After the installation is successful, click the window OK button to exit. Connect the computer USB to the development board and power on, and then enter the computer device manager, you can see that the CH340 port is identified under the port, as shown in the following picture:
Zažgite smetnjak file
- Open the “Flash_Download” folder in “8-快速使用_Quick_Start”, locate the “flash_download_tool” folder, open the folder, and double-click the exe executable file orodja flash_download_tool. Kot je prikazano na spodnji sliki:
- After opening the Flash download tool, ChipType select “ESP32”,WorkMode select “Develop”,LoadMode keep the default (UART), and then click “OK” button, as shown below:
Vstopite v vmesnik orodja za prenos Flash, najprej izberite koš file zažgati, smetnjak file in the data package “8-快速使用_Quick_Start /bin” directory, as shown in the following figure:
- Kliknite gumb s tremi pikami na sredini, da izberete koš file v zgornjih korakih. Po izbiri potrdite polje spredaj in nastavite naslov za zapisovanje na »0«, kot je prikazano na naslednji sliki:
- Set SPI SPEED to “80MHz”, SPI MODE to “DIO”, and keep other Settings default, as shown in the following figure:
- Set COM, as long as the product is normally connected to the computer, COM port will be automatically recognized, click the drop-down menu to select. Set BAUD, click the drop-down menu to select, the larger the value, the faster the burning speed, but can not exceed the maximum transmission rate supported by the USB-to-serial chip. As shown in the picture below:
- Click the “START” button to enter the burning state. During the burning process, the status changes: “Waiting for synchronous power-on” -> “Downloading” -> “FINISH”, and the progress bar will also be loaded, as shown in the following picture:
Zaženite program
Po smetnjaku file je zažgan, pritisnite gumb za ponastavitev izdelka ali znova vklopite izdelek in videli boste učinek delovanja programa, kot je prikazano na spodnji sliki:
Pogosto zastavljena vprašanja
- V: Kako vklopim izdelek?
A: Use a Type-C cable with power supply and data transmission function to connect the computer to the product. - V: Kako namestim gonilnik USB-v-serijska vrata?
A: Locate and decompress the USB-SERIAL_CH340.zip package, then run CH341SER.EXE for installation. - V: Kako naj zažgem smetnjak file?
A: Open the Flash_Download folder, run flash_download_tool, select ESP32 as ChipType, and follow the steps mentioned in the manual.
Dokumenti / Viri
 |
LCD-zaslon na dotik lcdwiki E32R40T [pdf] Uporabniški priročnik E32R40T, E32N40T, E32R40T LCD-zaslon na dotik, E32R40T, LCD-zaslon na dotik, Zaslon na dotik, Zaslon, Zaslon |