1. Uvod
The Plinkwirekb USB 10G Tester (Model PCM-KW-514) is a versatile diagnostic tool designed to quickly test the speed, signal protocol, and voltage status of various USB interfaces. It supports USB 2.0, USB 3.0, USB 3.1 Gen 1 (5Gbps), and USB 3.1 Gen 2 (10Gbps) for both Type-A and Type-C connections. This manual provides detailed instructions for its setup, operation, and maintenance to ensure accurate and efficient use.
2. Značilnosti izdelka
- Multi-Port USB Interface Testing: Supports quick testing of USB 2.0/3.0, USB Type-C 3.1/3.0, USB Hub speed, USB signal protocol, and voltage stanje.
- Združljivost kabla: Capable of testing USB 2.0, 3.0, and Type-C 3.1 extension cables, as well as male-to-male cables.
- Efficient PCBA Board Testing: Features plug-and-play identification for PCBA board 2.0/3.0 testing, improving signal quality and detection capabilities.
- Protocol Identification: Quickly identifies 10G and 5G protocol interfaces.
- LED indikatorji: Clear LED indicators for USB 2.0 (U2), USB 3.0 (U3), USB 3.1 Gen 2 (10G), and Overvoltage Zaščita (OVP).
- Overvoltage Protection (OVP) Warning: Alerts users if the test port voltage exceeds 5V to prevent device damage.
- Široka uporaba: Suitable for testing USB Type-A and Type-C interfaces on computers, notebooks, USB hubs, mobile hard drives, USB flash drives, and for factory testing, QC inspection, and laboratory use.
- Dizajn z dvojno glavo: Features both USB Type-A and Type-C connectors for broad compatibility.
3. Vsebina paketa
- 1 x Plinkwirekb USB 10G Tester (PCM-KW-514)
4. Specifikacije
| Parameter | Vrednost |
|---|---|
| Številka modela | PCM-KW-514 |
| Priključek A | USB 3.0 tip A moški |
| Priključek B | USB 3.1 tip-C moški |
| Hitrost USB 2.0 | 480 Mbps |
| USB 3.0 (USB 3.1 Gen 1) Speed | 5 Gbps |
| USB 3.1 (USB 3.1 Gen 2) Speed | 10 Gbps |
| Dimenzije | 6.3 x 4.8 x 1.2 palca (paket) |
| Teža | 1.06 unče (paket) |
5. Nastavitev
The Plinkwirekb USB 10G Tester is designed for plug-and-play operation. No software installation or external power supply is required. Simply connect the tester to the USB port or cable you wish to evaluate.
6. Navodila za uporabo
6.1 Osnovna operacija
To use the tester, simply plug the appropriate end (USB-A or USB-C) into the port or cable you want to test. The device will automatically begin its diagnostic process, and the results will be indicated by the illuminated LEDs.
6.2 USB Port Detection and LED Indicators
The tester features several LED indicators to display the detected USB protocol and status:
- U2 Indicator: Lights up when a USB 2.0 connection is detected.
- U3 Indicator: Lights up when a USB 3.0 (5Gbps) connection is detected.
- Indikator 10G: Lights up when a USB 3.1 Gen 2 (10Gbps) connection is detected.
- OVP Indicator: Lights up if an overvoltage condition is detected (voltage > 5 V).
Detection Logic:
- When testing a USB 2.0 port: The U2 indikator zasveti.
- When testing a USB 3.0 (5G) port: The U3 in U2 indicators will light up.
- When testing a USB 3.1 (10G) port: The 10G in U2 indicators will light up. The U3 indicator will not light up in this scenario.
6.3 Prekomerna glasnosttage Protection (OVP) Indication
The OVP indicator provides a critical safety warning. If the voltage at the test port exceeds 5V, the OVP LED will light up. This alerts the user to a potential overvoltage condition, which could damage connected devices. Disconnect the tester immediately if the OVP indicator illuminates and investigate the power source.
6.4 Testing USB Hubs and Devices
The tester can be used to verify the functionality and speed of USB hubs, mobile hard drives, and USB flash drives. Connect the tester to the device or hub's USB port, and observe the LED indicators to confirm the detected USB standard and voltage stanje.
7. Vzdrževanje
- Čiščenje: Use a soft, dry cloth to clean the exterior of the tester. Avoid using liquid cleaners or solvents.
- Shranjevanje: Tester shranjujte na hladnem in suhem mestu, stran od neposredne sončne svetlobe in ekstremnih temperatur.
- Ravnanje: Izogibajte se padcem naprave ali njeni izpostavljenosti močnim udarcem, saj lahko s tem poškodujete notranje komponente.
8. Odpravljanje težav
- No LEDs light up: Ensure the tester is fully inserted into a powered USB port. Check if the host device is providing power.
- Incorrect speed detected: Verify that the cable and the host port both support the desired USB standard. Some USB-C to USB-A adapters or cables may only support USB 2.0 or 3.0 speeds.
- OVP indicator lights up: Immediately disconnect the tester. This indicates an overvoltage condition (above 5V) which can damage devices. Investigate the power source or port for faults.
- Prekinjena povezava: Ensure all connections are secure and free from debris. Try testing with a different cable or port to isolate the issue.
9. Garancija in podpora
For any issues, defects, or questions regarding the Plinkwirekb USB 10G Tester, please contact the manufacturer or your point of purchase. Please refer to your purchase documentation for specific warranty terms and contact information. The manufacturer is committed to resolving product-related concerns promptly.