Jauarta 5V 1A UPS Uninterruptible Power Supply Module

Uvod

This manual provides essential instructions for the safe and efficient use of your Jauarta 5V 1A UPS Uninterruptible Power Supply Module. This module is designed to provide a stable 5V 1A output, powered by either an external 5V input or a connected lithium battery, ensuring continuous operation for your devices.

Glavne lastnosti vključujejo:

• Izhodna moč: Zagotavlja največji izhod 5V 1A.
• Overvoltage Zaščita: Automatically cuts off input when it exceeds 6V, switching to battery power.
• Zaščita pred povratno polarnostjo: Includes protection against reverse connection for both input and output.
• Zaščita pred kratkim stikom: Built-in protection against output short circuits.
• Istočasno polnjenje in praznjenje: Supports charging the battery while simultaneously supplying power to the load.

Pomembne varnostne informacije

• Polariteta baterije: The positive and negative electrodes of the battery must not be reversed. Reversing polarity will damage the module.
• Vhodna voltage: Zagotovite, da je vhodna voltage does not exceed 20V. Exceeding 20V can cause damage to the unit.
• Ožičenje: Due to potentially large currents, it is recommended to use thicker wires. The wire cross-section should be greater than 1.5mm².
• Izhodni tok: The maximum output current is 1A, but continuous 1A output may not be sustained under all conditions.
• Delovno okolje: Operate within the specified temperature range of -40°C to 85°C and humidity range of 0-95%RH.

Specifikacije

Vsebina paketa

Paket vključuje:

• 1 x Jauarta 5V 1A UPS Uninterruptible Power Supply Module

Nastavitev in povezava

Follow these steps to set up your UPS module:

1. Priključite vhodno napajanje: Connect the correct 5V input voltage to the designated input terminals (N+ and N-). Ensure polarity is correct.
2. Povežite baterijo: Connect your polymer lithium battery or lithium battery to the B+ and B- terminals. Observe correct polarity to prevent module damage. The recommended battery capacity is below 10000mA.
3. Preveri izhod: Before connecting your load, you may check the output voltage with a voltmeter and current with an ammeter at the OUT+ and OUT- terminals.
4. Povežite obremenitev: Connect your 5V device to the OUT+ and OUT- terminals.

Slika: Od zgoraj navzdol view of the Jauarta UPS module, highlighting the input (N+, N-), battery (B+, B-), and output (OUT+, OUT-) connection points.

Slika: Pod kotom view of the Jauarta UPS module, providing a general perspective of its components and layout.

Navodila za uporabo

The Jauarta UPS module operates automatically once connected. It will draw power from the 5V input when available and simultaneously charge the connected lithium battery. If the 5V input power is interrupted or falls below 6V, the module will seamlessly switch to drawing power from the connected battery to maintain a continuous 5V output to your device.

• Charging Indicator (Optional): Users can install a common anode red-green LED as a charging indicator. The red light indicates if the output terminal is loaded. The green light flashes to show battery capacity. If there is no load or battery, the green light will turn off.
• Power Continuity: The module ensures uninterrupted power supply during transitions between external power and battery power.

Vzdrževanje

The Jauarta UPS module is designed for low maintenance. To ensure optimal performance and longevity:

• Modul naj bo čist in brez prahu ter umazanije.
• Ensure proper ventilation around the module, especially during operation, to prevent overheating.
• Regularly inspect wiring for any signs of wear or damage.
• Store in a dry environment within the specified operating temperature and humidity ranges when not in use.

Odpravljanje težav

If you encounter issues with your UPS module, consider the following:

• Izhodna moč:
  • Check if the input power is correctly connected and within the 5V range.
  • Verify that the battery is connected with correct polarity and is charged.
  • Ensure there is no short circuit at the output terminals.
• Poškodba modula:
  • If the module is not functioning after initial connection, check if the battery or input power was connected with reversed polarity.
  • Potrdite, da je vnos voltage did not exceed 20V at any point.
• Občasno napajanje:
  • Ensure all wire connections are secure and that the wire thickness is adequate for the current draw (greater than 1.5mm² recommended).
  • Check the battery health and capacity.

Če težave ne odpravite, se za nadaljnjo pomoč obrnite na podporo strankam.

Garancija in podpora

This Jauarta product comes with a standard manufacturer's warranty. For specific warranty details, please refer to the product packaging or contact Jauarta customer support. For technical assistance or troubleshooting not covered in this manual, please reach out to our support team through the official Jauarta webspletno mesto ali vaš prodajalec.