Jauarta Coolant Level Sensor User Manual

1. Izdelek je končanview

The Jauarta Coolant Level Sensor is designed to detect low liquid levels in various applications, primarily for coolant systems. It operates as a normally open (NO) switch, activating an alarm or control device when the liquid level drops below the sensor's probe position. This sensor is suitable for non-corrosive liquids with electrical resistivity similar to water.

Slika 1: Konecview of the Jauarta Coolant Level Sensor.

2. Specifikacije

3. Vsebina paketa

Preverite, ali so v paketu prisotni vsi elementi:

• 1 x Coolant Level Sensor
• 6 x Accessories (e.g., connectors, seals)

Figure 2: Package contents including the sensor and accessories.

4. Varnostne informacije

• Always disconnect power before installation or maintenance to prevent electrical shock.
• Ensure proper wiring connections according to the specified voltage in trenutne ocene.
• Do not use the sensor with corrosive liquids unless explicitly stated as compatible.
• Handle the sensor with care to avoid damage to the probe or electrical terminals.
• Če niste prepričani o postopku, naj namestitev opravi usposobljeno osebje.

5. Nastavitev in namestitev

The Jauarta Coolant Level Sensor is designed for straightforward installation using its 1/2NPT thread. Follow these steps for proper setup:

1. Prepare the Installation Point: Identify a suitable location in your liquid reservoir or tank where the 1/2NPT thread can be securely mounted. Ensure the probe will be at the desired low-level detection point.
2. Privijte senzor: Carefully thread the sensor into the prepared 1/2NPT opening. Use appropriate thread sealant (e.g., PTFE tape) to ensure a watertight seal. Do not overtighten.
3. Povežite ožičenje: The sensor features a triode open collector (OC) output. Connect the positive (+) terminal to your 5-35VDC power supply and the negative (-) terminal to the common ground. The output (OC) terminal should be connected to your control device or alarm input. Refer to the wiring diagram of your specific control system for correct integration.
4. Preverite povezave: Double-check all electrical connections for polarity and security before applying power.

Figure 3: Sensor showing 1/2NPT threads for installation.

Figure 4: Electrical terminals for wiring connections.

6. Navodila za uporabo

The Jauarta Coolant Level Sensor operates as a normally open (NO) switch. This means:

• When the liquid level is zgoraj the sensor's probe, the switch remains open, and no signal is outputted from the OC terminal.
• When the liquid level drops spodaj the sensor's probe, the switch closes, and the sensor outputs a signal (switch closure) to the connected generator control device or alarm system.

The sensor requires a working voltage between 5VDC and 35VDC. The triode open collector (OC) output can handle a maximum current of 100mA and a maximum working voltage of 35VDC at the output end. Ensure your connected device's input specifications are compatible with these output characteristics.

7. Vzdrževanje

To ensure reliable operation and longevity of your Jauarta Coolant Level Sensor, consider the following maintenance guidelines:

• Redni pregled: Periodically inspect the sensor for any signs of physical damage, corrosion, or buildup on the probe.
• Čiščenje: If buildup is observed on the probe, carefully clean it using a soft cloth and a mild, non-abrasive cleaner. Ensure the system is drained and power is disconnected before cleaning.
• Preverjanje povezave: Preverite, ali so vse električne povezave varne in brez korozije.
• Okoljski pogoji: Ensure the sensor is operating within its specified environmental conditions to prevent premature failure.

8. Odpravljanje težav

If you encounter issues with your Jauarta Coolant Level Sensor, consider the following troubleshooting steps:

• Senzor se ne sproži:
  • Check if the liquid level is actually below the probe.
  • Verify power supply to the sensor (5-35VDC).
  • Inspect wiring connections for looseness or incorrect polarity.
  • Check for excessive buildup on the sensor probe that might prevent detection.
• False Alarms/Constant Triggering:
  • Ensure the liquid level is consistently above the probe.
  • Check for electrical interference or faulty wiring.
  • Verify the sensor is not being used with a liquid it is incompatible with, which might affect its electrical properties.
• No Power/Indicator:
  • Confirm the power source is active and providing the correct voltage.
  • Check all fuses or circuit breakers in the power circuit.

Če težave po izvedbi teh preverjanj ne izginejo, se za dodatno pomoč obrnite na podporo strankam.

9. Garancija in podpora

Jauarta products are manufactured to high-quality standards. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included with your purchase or visit the official Jauarta webza podrobne garancijske pogoje.

For technical support, troubleshooting assistance, or warranty claims, please contact Jauarta customer service through the retailer where the product was purchased or via the contact information provided on the official Jauarta webmesto.