REPTITRIP 8.5-Inch Day/Night Thermostatic Reptile Heat Lamp Uporabniški priročnik

1. Uvod

This manual provides essential instructions for the safe and effective use of your REPTITRIP 8.5-Inch Day/Night Thermostatic Reptile Heat Lamp. This system is designed to provide a controlled heating environment for reptiles, simulating natural day-night temperature cycles. It includes a ceramic heat emitter, a light fixture, and a dimming thermostat for precise temperature regulation.

2. Varnostne informacije

• Opozorilo o visoki temperaturi: Toplota lamp surface can reach high temperatures during operation. A warning sticker on the lamp turns red at 113°F (45°C) to indicate this.
• Umestitev: Always keep a safe distance between the heat lamp and flammable materials, as well as your reptiles, to prevent burns or fire hazards.
• Indoor Dry Use Only: This product is intended for indoor, dry environments. Do not expose to water or high humidity.
• Združljivost žarnice: This fixture is compatible with reptile heat bulbs and ceramic heat emitters up to 150W. It is ni združljivo with LED lights or sun lamps.
• Električna varnost: Prepričajte se, da napajalnik ustreza glasnosti izdelkatage requirements (100-120 Volts, 60 Hertz). Do not overload electrical outlets.

Image: Close-up of the warning sticker on the heat lamp, indicating 'CAUTION: HOT SURFACE AVOID CONTACT FOR INDOOR DRY USE ONLY'.

3. Kaj je v škatli

Po razpakiranju preverite, ali so prisotne vse komponente:

• 8.5-INCH Reptile Light Fixture
• Reptile Thermostat
• 150W Ceramic Heat Emitter

Image: The complete REPTITRIP reptile heat lamp system, including the 8.5-inch lamp fixture, the digital thermostat controller, and the ceramic heat emitter bulb.

4. Navodila za nastavitev

1. Install the Ceramic Heat Emitter: Carefully screw the 150W ceramic heat emitter into the E26 socket of the 8.5-inch light fixture. Ensure it is securely tightened but do not overtighten.
2. Position the Light Fixture: Place the light fixture securely above your reptile enclosure. Use the integrated hanging hook if suspending the lamp. Ensure adequate clearance from the enclosure walls and any inhabitants.
3. Priključite termostat: Plug the light fixture's power cord into the designated output on the REPTITRIP thermostat controller.
4. Position the Temperature Probe: Carefully place the temperature probe inside the reptile enclosure. Position it in the area where you want to maintain a stable temperature, typically near the basking spot or a central location, ensuring it is not directly under the heat lamp or accessible to your pet.
5. Vklop: Plug the thermostat's power cord into a suitable electrical outlet.

5. Navodila za uporabo

The REPTITRIP thermostat allows for precise control over day and night temperatures, simulating natural circadian cycles. Refer to the LCD display and buttons for programming.

Slika: Podrobna view of the thermostat's LCD screen showing current time, ambient temperature, output power, and set temperature, along with the SET, OK, plus, and minus buttons.

Osnovno delovanje:

1. Vklop/izklop: Dolgo pritisnite OK gumb za vklop ali izklop termostata.
2. Vstopite v nastavitveni način: Dolgo pritisnite NASTAVI gumb za vstop v nastavitveni način.
3. Prilagodi vrednosti: Uporabite + in - gumbi za prilagajanje vrednosti.
4. Confirm/Toggle: Pritisnite OK button to confirm a setting or toggle between different parameters within the setting mode.
5. Shrani nastavitve: After adjusting a setting, long press the NASTAVI gumb za shranjevanje in izhod iz nastavitvenega načina.

Setting Day/Night Temperatures (Example):

Follow these steps to program your desired day and night temperatures and times. An example setting is provided for clarity.

• Trenutni čas: 10:00 zjutraj
• T1 (Day Start Time): 7:20 zjutraj
• SV (Daytime Target Temp): 100°F
• T2 (Night Start Time): 6:30
• SV (Nighttime Target Temp): 80°F

1. Nastavi trenutni čas: Dolg pritisk NASTAVI to enter setup mode. Adjust the time using +/-. Pritisnite OK to move between hours and minutes. Long press NASTAVI again to save and proceed to T1 time setting.
2. Set Day Start Time (T1): Adjust T1 to 7:20 AM using +/-. After T1 is set, press OK to toggle to the Daytime Target Temperature setting.
3. Set Daytime Target Temperature: Adjust the daytime target temperature to 100°F using +/-. Dolg pritisk NASTAVI to save and proceed to T2 time setting.
4. Set Night Start Time (T2): Adjust T2 to 6:30 PM using +/-. After T2 is set, press OK to toggle to the Nighttime Target Temperature setting.
5. Set Nighttime Target Temperature: Adjust the nighttime target temperature to 80°F using +/-. Dolg pritisk NASTAVI to save all settings and exit.

Image: A visual guide illustrating the process of setting distinct day and night temperatures and their corresponding start times on the thermostat for a 24-hour cycle.

Image: A reptile terrarium setup demonstrating the heat lamp in operation, with the thermostat displaying the current day and night temperature settings, emphasizing the importance of diurnal temperature variations.

Image: A graph depicting temperature fluctuations over a 24-hour period, showing how the thermostat maintains a stable daytime temperature (orange line) and a stable nighttime temperature (blue line) for optimal reptile health.

6. Vzdrževanje

• Čiščenje: Disconnect power before cleaning. Wipe the exterior of the lamp fixture and thermostat with a dry, soft cloth. Do not use abrasive cleaners or immerse any part in water.
• Zamenjava žarnice: Zagotovite lamp is unplugged and completely cool before attempting to replace the ceramic heat emitter. Handle the new bulb carefully and screw it in firmly.
• Pregled sonde: Periodically check the temperature probe for any damage or debris that might affect its accuracy.

7. Odpravljanje težav

• Lamp Brez ogrevanja:
  • Check if the thermostat is powered on and plugged in correctly.
  • Verify the ceramic heat emitter is screwed in properly and not burnt out. Replace if necessary.
  • Ensure the set temperature is above the current ambient temperature.
• Temperaturna nihanja:
  • Ensure the temperature probe is correctly positioned and not directly exposed to drafts or direct heat from the lamp.
  • Check for external factors affecting terrarium temperature, such as room temperature changes.
• Difficulty Programming:
  • Refer to the 'Operating Instructions' section and the provided video for detailed steps.
  • Prepričajte se, da dolgo pritiskate NASTAVI button to enter and save settings, and short-pressing OK to toggle between parameters.

8. Specifikacije

Image: A visual representation of the product specifications, including input voltage, output load, temperature setting range, and control mode, as seen on the thermostat's display.

Compatible Heating Devices:

• Ceramic Heat Emitters
• Daytime Heat Bulbs
• Infrared Heat Bulbs

Incompatible Heating Devices:

• LED UVB žarnice
• UVA UVB Sun Bulbs
• Kompaktna fluorescentna Lamps

Image: A chart detailing which types of reptile heating devices are compatible with the REPTITRIP system (Ceramic Heat Emitter, Daytime Heat Bulbs, Infrared Heat Bulbs) and which are not (LED UVB Bulbs, UVA UVB Sun Bulbs).

9. Garancija in podpora

Warranty information for this product is not provided in the current documentation. For specific warranty details, technical support, or customer service inquiries, please contact REPTITRIP directly through their official channels or the retailer from whom the product was purchased.