Thincol Digital Temperature Controller (12V Model) User Manual

1. Uvod

This manual provides detailed instructions for the installation, operation, and maintenance of your Thincol Digital Temperature Controller (12V Model). Please read this manual thoroughly before using the device to ensure proper function and safety.

2. Varnostne informacije

Pomembna varnostna navodila:

• Prepričajte se, da je napajalnik voltage matches the device's requirements (DC 12V for this model).
• Naprave ne izpostavljajte vodi ali prekomerni vlagi.
• Avoid installing the device in areas with extreme temperatures or direct sunlight.
• Pred kakršnim koli ožičenjem ali vzdrževanjem izklopite napajanje.
• All wiring should be performed by a qualified professional if you are unsure.
• Hraniti izven dosega otrok.

3. Vsebina paketa

Paket naj vsebuje naslednje predmete:

• 1 x Thincol Digital Thermostat Temperature Alarm Controller Sensor (12V Model)

4. Izdelek je končanview

Familiarize yourself with the components of your temperature controller.

Slika 1: Spredaj view of the Thincol Digital Temperature Controller, showing the dual LED display (PV and SV), 'SET' button, up/down arrows, 'OUT' indicator, and 'Restart' button. The temperature sensor probe is connected via a black wire.

Slika 2: Zadaj view of the Thincol Digital Temperature Controller, highlighting the blue screw terminals for power input and output connections.

Slika 3: stran view of the Thincol Digital Temperature Controller, showing its compact form factor suitable for panel mounting.

Ključne komponente:

• PV zaslon: Process Value (Current Temperature)
• Zaslon SV: Set Value (Target Temperature)
• Gumb SET: Enters/Exits parameter setting mode.
• Gumbi gor/dol: Prilagodite vrednosti v načinu nastavitev.
• Indikator OUT: Illuminates when the output relay is active.
• Gumb za ponovni zagon: Ponastavi napravo.
• Sponke za ožičenje: For power input and load output connections.
• Senzor temperature: Measures the ambient temperature.

5. Specifikacije

6. Nastavitev in ožičenje

Before wiring, ensure the power supply is disconnected. Incorrect wiring can damage the device or connected equipment. If you are unsure, consult a qualified electrician.

Žične povezave:

1. Vhodna moč: Connect the DC 12V power supply to the designated input terminals on the back of the controller. Observe polarity (+/-) carefully.
2. Izhodna obremenitev: Connect the device you wish to control (e.g., heating element, cooling fan) to the output terminals. The controller acts as a switch for this load. Ensure the load's power requirements do not exceed the controller's maximum output (120W for the 12V model).
3. Senzor temperature: Insert the temperature sensor probe into the environment where temperature measurement is required. Ensure it is securely placed and not directly exposed to heat sources or drafts that could skew readings.

Warning: Always disconnect power before making or changing any wiring connections.

7. Navodila za uporabo

Setting the Target Temperature (SV):

1. Pritisnite NASTAVI enkrat pritisnite gumb. Prikaz SV (nastavljena vrednost) bo začel utripati.
2. Uporabite Up in Dol arrow buttons to adjust the target temperature to your desired value.
3. Pritisnite NASTAVI button again to confirm the setting and exit the setting mode.

Cooling/Heating Mode Selection:

The controller can operate in either cooling or heating mode. This is typically configured via an advanced parameter (often labeled P0 or P1). Please consult the full product manual for specific instructions on how to access and set the cooling or heating mode.

Advanced Parameter Settings (P3, P4, P5):

To access advanced parameters, typically a long press of the NASTAVI button is required. Use the Up/Down buttons to navigate between parameters (e.g., P0, P1, P2, P3, P4, P5) and then press NASTAVI again to enter the parameter's value adjustment mode.

• P3 Setting (Delay Stop/Compressor Protection): If P3 is set to '1', the thermostat will stop running for 1 minute. This function is often used for compressor delay protection in cooling systems. A long press of the NASTAVI button is required to trigger this function again after it has completed its cycle.
• P4 Setting (Delayed Start): If P4 is set to '1', the thermostat will begin operation after a 1-minute delay. During this delay, the digital display will not illuminate until normal operation commences. A long press of the NASTAVI button is required to trigger this function again.
• P5 Setting (Parameter Lock): By default, P5 is set to 'OFF'. Once the desired temperature and other parameters are configured, setting P5 to 'ON' will lock the data, preventing accidental changes. To modify settings again, P5 must be set back to 'OFF'.

Kalibracija temperature:

The device supports temperature calibration to fine-tune accuracy. This is usually an advanced parameter (e.g., P7 or P8). Refer to the full product manual for specific instructions on how to access and adjust the temperature calibration offset.

High/Low Limit Temperature Setting:

The controller allows setting upper and lower temperature limits to prevent extreme conditions. These are typically accessible through advanced parameters. Consult the full product manual for details on setting these limits.

8. Vzdrževanje

• Čiščenje: Napravo obrišite z mehko, suho krpo. Ne uporabljajte abrazivnih čistil ali topil.
• Skrb za senzor: Ensure the temperature sensor is clean and free from debris for accurate readings.
• Preverjanje povezave: Občasno preverite vse ožičene povezave, da se prepričate, da so varne.
• Shranjevanje: If storing the device for an extended period, disconnect it from power and store it in a dry, cool place.

9. Odpravljanje težav

10. Garancija in podpora

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Thincol customer service directly. Keep your purchase receipt for warranty claims.

Manufacturer: Thincol