1. Nastavitev
This section guides you through the initial preparation of your Brother LS-1217 sewing machine before its first use.
1.1 Razpakiranje in namestitev
Carefully remove the sewing machine from its packaging. Retain all packing materials for future transport or storage. Place the machine on a stable, flat surface with adequate lighting. Ensure there is enough space around the machine for comfortable operation and fabric handling.
1.2 Napajalni priključek
Connect the power cord to the machine's power input jack, then plug the other end into a standard electrical outlet. Ensure the power switch is in the "OFF" position before connecting. The foot controller also connects to a dedicated jack on the machine.
1.3 Namestitev igle
- Obrnite ročno kolo proti sebi, da dvignete iglo v najvišji položaj.
- Odvijte iglo clamp Vijak privijte tako, da ga zavrtite v nasprotni smeri urinega kazalca.
- Vstavite novo iglo z ravno stranjo obrnjeno proti zadnji strani stroja in jo potisnite navzgor, kolikor gre.
- Zategnite iglo klamp varno privijte.
1.4 Navijanje vretenca
Proper bobbin winding is crucial for even stitching.
- Na zatič za navijanje položite tuljavo niti.
- Napeljite nit skozi zgornje vodilo niti in okoli napenjalnega diska za navijanje vretenca.
- Insert the thread end into the small hole on the bobbin, from the inside out.
- Namestite vreteno na vreteno navijalca vretenca in ga potisnite v desno.
- Press the foot controller gently to start winding. Stop when the bobbin is full and evenly wound.
- Cut the thread, push the spindle back to the left, and remove the bobbin.
1.5 Vdevanje niti v stroj
Follow these steps for correct upper and lower threading.
Zgornja nit:
- Dvignite tačko in iglo v najvišji položaj.
- Namestite tuljavo niti na zatič za tuljavo.
- Napeljite nit skozi zgornje vodilo niti.
- Pass the thread down into the tension discs, then up and through the take-up lever from right to left.
- Guide the thread down through the remaining thread guides and finally through the eye of the needle from front to back.
- Pull about 6 inches of thread under the presser foot and towards the back.
Spodnja nit (vstavljanje vretenca):
- Odprite pokrov vretenca.
- Vstavite navito vreteno v vreteno in pazite, da se nit odvija v nasprotni smeri urinega kazalca.
- Guide the thread into the tension spring of the bobbin case.
- Zaprite pokrov vretenca.
- Hold the upper thread lightly, turn the handwheel towards you to lower and raise the needle, catching the bobbin thread. Pull both threads under the presser foot and to the back.
2. Upravljanje stroja
This section details the basic operations for sewing with your Brother LS-1217.
2.1 Basic Stitch Selection
Your machine offers various stitch patterns. To select a stitch, turn the pattern selection dial until the desired stitch symbol aligns with the indicator mark. Refer to the stitch chart on your machine for available options.
2.2 Fabric Placement
Place the fabric under the presser foot, aligning the edge with the desired seam allowance guide on the needle plate. Lower the presser foot using the presser foot lever.
2.3 Začetek šivanja
With the presser foot lowered, gently press the foot controller. The machine will begin to sew. Guide the fabric gently; do not pull or push it, as this can bend the needle or affect stitch quality.
2.4 Obrnjeno šivanje
To secure the beginning and end of a seam, use the reverse stitch lever. Press and hold the lever while sewing to stitch backward. Release the lever to resume forward stitching.
2.5 Zaključevanje šiva
When you reach the end of your seam, perform a reverse stitch for a few stitches, then release the foot controller. Raise the needle to its highest position and lift the presser foot. Pull the fabric towards the back, then cut the threads using the thread cutter on the machine or scissors, leaving about 4-6 inches of thread tails.
3. Vzdrževanje
Regular maintenance ensures the longevity and optimal performance of your Brother LS-1217.
3.1 Čiščenje stroja
Lint and dust can accumulate in the bobbin area and feed dogs, affecting stitch quality. Disconnect the machine from power before cleaning.
- Odstranite iglo, tačko in ploščico igle.
- Use the small brush provided with your machine (or a soft brush) to remove lint from the bobbin case, feed dogs, and surrounding areas.
- Do not use compressed air, as it can push lint further into the machine.
- Zunanjost naprave obrišite z mehko, suho krpo.
3.2 Mazanje
The Brother LS-1217 is designed to be largely maintenance-free regarding lubrication. Avoid applying oil unless specifically instructed by a qualified service technician, as improper lubrication can cause damage.
3.3 Zamenjava igle
Replace the needle regularly (approximately every 8-10 hours of sewing or after every major project) and immediately if it becomes bent, dull, or burred. A damaged needle can cause skipped stitches, thread breakage, and fabric damage. Refer to section 1.3 for installation instructions.
4. Odpravljanje težav
Ta razdelek obravnava pogoste težave, na katere lahko naletite, in ponuja rešitve.
| Težava | Možen vzrok | rešitev |
|---|---|---|
| Preskočeni šivi | Nepravilna namestitev igle, upognjena igla, napačna vrsta igle za blago, nepravilno napeljevanje niti. | Reinstall needle correctly (flat side to back), replace bent needle, use appropriate needle for fabric, rethread machine completely. |
| Zlom niti | Improper threading, incorrect tension, damaged needle, poor quality thread, bobbin wound unevenly. | Rethread machine, adjust tension, replace needle, use good quality thread, rewind bobbin evenly. |
| Fabric Jamming / Bunching | Improper threading, presser foot not lowered, excessive pulling/pushing of fabric, lint buildup. | Rethread machine, ensure presser foot is down, guide fabric gently, clean bobbin area and feed dogs. |
| Neenakomerni šivi | Incorrect tension settings, improper threading, dull needle, inconsistent fabric feeding. | Adjust upper and lower thread tension, rethread machine, replace needle, ensure consistent fabric guidance. |
| Stroj se ne zažene | Power cord not connected, power switch off, foot controller not connected, bobbin winder spindle engaged. | Check power connections, turn power switch on, connect foot controller, disengage bobbin winder spindle. |
If these solutions do not resolve the issue, please contact customer support or a qualified service technician.
5. Specifikacije
Key technical specifications for the Brother LS-1217 Sewing Machine.
- Model: Brother LS-1217
- Vrste šivov: Multiple utility and decorative stitches (e.g., Straight, Zigzag, Buttonhole)
- Sistem igel: HAx1 (130/705H)
- Napajanje: AC 110-120V, 60Hz (North America) / AC 220-240V, 50Hz (Europe/Asia) - (Note: Actual voltage depends on region)
- Dimenzije (pribl.): 15.4" x 6.7" x 11.4" (39 cm x 17 cm x 29 cm)
- Teža (pribl.): 11 lbs (5 kg)
- Največja hitrost šivanja: Do 750 šivov na minuto
- Osvetlitev: Built-in sewing light
6. Garancija in podpora
For detailed warranty information, please refer to the warranty card included with your original purchase or visit the official Brother support webspletnega mesta. Shranite dokazilo o nakupu za uveljavljanje garancije.
Podpora strankam: For technical assistance, parts, or service, please contact Brother customer support. Contact details can typically be found on the Brother official webspletnem mestu ali v dokumentaciji izdelka.
Spletni viri: Additional resources, FAQs, and video tutorials may be available on the official Brother support webmesto.