Navodila za uporabo

Uvod

The Palmer POCKET AMP BASS (PEPAMPBASS) is a versatile, portable preamp and effects pedal designed for active and passive bass guitars. It offers extensive sound shaping capabilities, making it suitable for various applications including gigging, recording, and practice. This manual provides detailed instructions for its setup, operation, and maintenance.

Varnostne informacije

• Pred uporabo naprave natančno preberite vsa navodila.
• Enote ne izpostavljajte dežju ali vlagi.
• Zagotovite ustrezno prezračevanje; ne blokirajte prezračevalnih odprtin.
• Use only the specified power supply (9V DC, 200mA, center negative).
• Med nevihtami ali če naprave dalj časa ne uporabljate, izklopite napajanje.
• Za vse servise se obrnite na usposobljeno servisno osebje.

Vsebina paketa

• Palmer POCKET AMP BASS (PEPAMPBASS) unit
• Navodila za uporabo (ta dokument)
• Note: Power adapter is not included.

Kontrole in povezave

Sprednja plošča je končanaview

Figure 1: Front panel of the Palmer POCKET AMP BASS, highlighting the input and output connections for instrument, headphones, and auxiliary devices.

• Bass In: 1/4" TS input jack for connecting your bass guitar.
• Normal/PAD -12dB Switch: Selects input sensitivity. Use "PAD -12dB" for active basses with high output to prevent clipping.
• Telefoni: 1/8" TRS stereo output jack for connecting headphones.
• Aux vhod: 1/8" TRS stereo input jack for connecting external audio sources like an MP3 player or smartphone for practice.
• Bass Thru: 1/4" TS output jack for sending the unprocessed bass signal directly to another amplifier or device.

Nadzor na zgornji plošči

Figure 2: Top panel of the Palmer POCKET AMP BASS, displaying the various knobs and switches for tone shaping and effects.

• MODE Switch (Fuzz, O.DRIVE, CLEAN): Selects the primary sound mode.
  • ČISTO: Provides a transparent, uncolored bass tone.
  • O.DRIVE: Adds a warm, natural overdrive.
  • FUZZ: Delivers a thick, aggressive fuzz effect.
• Gumb DRIVE: Adjusts the amount of gain or distortion for the O.DRIVE and FUZZ modes.
• BLEND Knob (Dry/Wet): Mixes the direct (dry) signal with the processed (wet) signal. Fully counter-clockwise is 100% dry, fully clockwise is 100% wet.
• SATURATE Knob: Controls the saturation and compression characteristics of the tone.
• Gumb VOL: Prilagodi skupno izhodno glasnost enote.
• F.SW Switch (MUTE/BYPASS): Controls the footswitch function.
  • MUTE: Footswitch mutes the output.
  • OBMOČEK: Footswitch toggles between active effect and true bypass.
• CAB Switch (FLAT, MODERN, VINTAGE): Selects the cabinet simulation type.
  • STANOVANJE: No cabinet simulation, providing a raw, direct sound.
  • MODERNO: Simulates a modern bass cabinet with full-range response.
  • VINTAGE: Offers a warmer, more colored sound reminiscent of classic bass cabinets.
• Gumb BASS: Adjusts the low-frequency response (EQ).
• LEVEL Knob (Mid EQ): Adjusts the gain/cut of the selected mid-frequency.
• FREQ Knob (Mid EQ): Selects the center frequency for the semi-parametric mid-range EQ.
• HIGHS Knob: Adjusts the high-frequency response (EQ).
• Nožno stikalo: Engages/disengages the effect or mutes the output, depending on the F.SW setting.

Priključki na zadnji plošči

Figure 3: Rear panel of the Palmer POCKET AMP BASS, detailing the balanced DI output, effects loop, and power input.

• DI Out (Balanced XLR): Balanced XLR output for direct connection to a mixing console or audio interface.
  • Stikalo PRED/POST: Determines whether the DI output signal is taken before (PRE) or after (POST) the internal effects and EQ.
  • Stikalo GND/LIFT: Ground lift switch to eliminate hum caused by ground loops.
• TO AMP (1/4" TS): Unbalanced 1/4" TS output for connecting to a bass amplifier.
• FX Insert (1/4" TRS): Stereo 1/4" TRS jack for connecting external effects pedals in a send/return loop. Tip is Send, Ring is Return.
• DC 9V (200mA, Center Negative): Power input jack for a 9V DC power adapter.

Nastavitev

1. Napajalni priključek: Connect a 9V DC, 200mA, center negative power adapter (not included) to the "DC 9V" input on the rear panel. Alternatively, the unit can be powered by a 9V battery (located in the compartment on the bottom).
2. Priključek instrumenta: Plug your bass guitar into the "Bass In" jack on the front panel. If using an active bass with high output, set the "Normal/PAD -12dB" switch to "PAD -12dB".
3. Izhodna povezava:
   • For headphones: Connect headphones to the "Phones" jack.
   • Za an amplifier: Connect the "TO AMP" jack to your bass ampprispevek uporabnika za življenje.
   • For a mixing console/audio interface: Connect the "DI Out" XLR to the console/interface. Adjust the "PRE/POST" and "GND/LIFT" switches as needed.
4. Pomožni vhod: To play along with external audio, connect your audio source (e.g., smartphone) to the "Aux In" jack. The volume of the auxiliary input is controlled by the source device.
5. Effects Loop (Optional): To integrate external effects, connect a TRS cable from the "FX Insert" jack to your effects pedal(s). The Tip of the TRS cable is the Send, and the Ring is the Return.

Navodila za uporabo

The Palmer POCKET AMP BASS offers a range of controls to shape your bass tone. Experiment with the settings to find your desired sound.

Sound Modes and Drive

• Uporabite NAČIN switch to select between CLEAN, O.DRIVE, and FUZZ.
• Prilagodite VOZI knob to control the intensity of the overdrive or fuzz effect. Start with lower settings and increase gradually.
• The NASIČITI knob adds harmonic richness and compression. Higher settings will increase sustain and density.
• The MEŠAJ knob allows you to mix your original clean bass signal with the processed signal. This is particularly useful for retaining low-end clarity when using distortion effects.

Izenačitev (EQ)

• The BASS knob boosts or cuts low frequencies.
• The VISOKI knob boosts or cuts high frequencies.
• The mid-range EQ is semi-parametric:
  • Uporabite FREKV knob to select the specific mid-frequency you wish to adjust.
  • Uporabite STOPNJA knob to boost or cut the selected mid-frequency.

Cabinet Simulation

• The KABINA switch allows you to select between three different cabinet simulations:
  • STANOVANJE: Bypasses cabinet simulation.
  • MODERNO: Provides a clear, full-range sound typical of modern bass cabinets.
  • VINTAGE: Offers a warmer, more colored sound reminiscent of classic bass cabinets.

Footswitch Functionality

• Nastavite F.SW switch to either MUTE or BYPASS to define the footswitch's action.
• Press the footswitch to activate the selected function.

Vzdrževanje

• Napravo očistite z mehko, suho krpo. Ne uporabljajte abrazivnih čistil ali topil.
• Izogibajte se izpostavljanju enote ekstremnim temperaturam, vlagi ali neposredni sončni svetlobi.
• When not in use for extended periods, remove the 9V battery to prevent leakage.

Odpravljanje težav

Specifikacije

Garancija in podpora

For warranty information and technical support, please refer to the official Palmer webali se obrnite na lokalnega prodajalca. Shranite dokazilo o nakupu za morebitne garancijske zahtevke.

Za dodatno pomoč lahko obiščete Palmer Store on Amazon.