Pedrollo UPm2/3-GE Multi-StagUporabniški priročnik za potopno električno vodno črpalko e

1. Izdelek je končanview

The Pedrollo UPm2/3-GE is a multi-stage submersible electric water pump designed for efficient and reliable operation with clean water. Its innovative patented technical solutions ensure consistent performance, even after long periods of inactivity. This pump is suitable for various applications including domestic, civil, and agricultural water supply systems, pressure boosting, and garden irrigation.

Image 1: Pedrollo UPm2/3-GE Multi-Stage Submersible Electric Water Pump. This image shows the main unit of the submersible pump, highlighting its compact cylindrical design and the power cable connection.

Ključne značilnosti:

• Multi-stage submersible design: Ensures high efficiency and reliable water delivery.
• Independent floating impellers (patented): Prevents impeller seizing, even after extended periods of non-use.
• Double mechanical seals with oil chamber: Provides enhanced durability and protection against water ingress.
• Kompaktna velikost: Approximately 20% more compact than previous designs.
• Reduced energy consumption: Optimized for energy efficiency.
• Raised suction port: Designed to prevent the passage of sand, leaves, and other external particles that could block the hydraulic section and limit performance.
• Integrated float switch: For automatic operation based on water levels.

2. Varnostne informacije

Read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, serious injury, or property damage.

• Električna varnost: Ensure the power supply matches the pump's requirements (230V, 50Hz). Always disconnect power before performing any maintenance or installation. Use a ground fault circuit interrupter (GFCI) for electrical connections.
• Profesionalna namestitev: Electrical connections and initial setup should ideally be performed by a qualified electrician or technician.
• Kakovost vode: This pump is designed for clean water. Do not use it for flammable, corrosive, or abrasive liquids, or liquids with excessive solid content (maximum sand content 150 g/m³).
• Temperaturne omejitve: Do not operate the pump with liquid temperatures exceeding +40 °C.
• Zaščita kabla: Do not pull or carry the pump by its power cable. Protect the cable from sharp objects, heat, and oil.
• Otroci in hišni ljubljenčki: Keep children and pets away from the pump's operating area.

3. Nastavitev in namestitev

Pravilna namestitev je ključnega pomena za delovanje in dolgo življenjsko dobo črpalke. Upoštevajte naslednja navodila:

3.1 Razpakiranje in pregled

• Previdno vzemite črpalko iz embalaže.
• Inspect the pump for any visible damage that may have occurred during shipping. Do not install a damaged pump.
• Verify that all components, including the 20-meter power cable and float switch, are present.

3.2 Placement and Submersion

• The pump can be installed in both vertical and horizontal positions. Ensure it is placed on a stable, level surface to prevent movement during operation.
• The maximum submersion depth for this pump is 20 metrov. Ensure the power cable is sufficiently long and securely routed to avoid tension or damage.
• Ensure the pump is fully submerged in the liquid to be pumped. The raised suction port helps prevent blockages, but avoid placing the pump directly on a muddy or sandy bottom if possible.

3.3 Električna povezava

• Črpalko priključite na enofazno napajanje 230 V, 50 Hz.
• Always use a properly grounded outlet and a GFCI for protection.
• Ensure all electrical connections are watertight and protected from moisture.

3.4 Outlet Connection

• Connect a suitable pipe or hose to the pump's 1¼" outlet.
• Prepričajte se, da so vse povezave tesne, da preprečite puščanje.

Image 2: Close-up of Pedrollo UPm2/3-GE pump components. This image provides a closer look at the pump's construction, potentially showing the outlet, power cable entry, or float switch attachment point.

4. Navodila za uporabo

The Pedrollo UPm2/3-GE pump is designed for continuous service (S1) and features an integrated float switch for automatic operation.

4.1 Prvi zagon

• Ensure the pump is correctly installed and fully submerged in water.
• Plug the pump into a grounded and GFCI-protected power outlet.
• The float switch will activate the pump automatically when the water level rises to a predetermined height and deactivate it when the water level drops.

4.2 Automatic Operation with Float Switch

• The float switch is a safety and convenience feature. It prevents the pump from running dry, which can cause damage.
• Adjust the float switch cable length to set the desired ON/OFF water levels. A longer cable loop will result in a wider operating range (higher ON level, lower OFF level).
• Ensure the float switch can move freely without obstruction.

4.3 Manual Operation (if applicable)

This model primarily operates automatically via the float switch. For specific manual override instructions, consult a qualified technician or the full manufacturer's manual if available.

5. Vzdrževanje

Regular maintenance ensures optimal performance and extends the lifespan of your Pedrollo pump.

5.1 Generalno čiščenje

• Periodically remove the pump from the water and inspect the suction port for any debris (sand, leaves, etc.) that may have accumulated despite the raised design. Clean as necessary.
• Ensure the float switch is clean and moves freely.

5.2 Priprava na zimo (za hladno podnebje)

• In areas where temperatures drop below freezing, remove the pump from the water before winter.
• Clean the pump thoroughly and store it in a dry, frost-free location.

5.3 Pregled rotorja

• While the patented impellers are designed to prevent seizing, if you notice a significant drop in performance, it may be necessary to inspect the impellers for wear or blockages. This procedure should be performed by a qualified technician.

6. Odpravljanje težav

Preden se obrnete na podporo, ponovnoview te pogoste težave in rešitve:

For issues not listed here or if troubleshooting steps do not resolve the problem, please contact a qualified service technician or Pedrollo customer support.

7. Specifikacije

8. Garancija in podpora

For warranty information, please refer to the documentation provided with your purchase or contact the retailer. Pedrollo products are manufactured to high standards, and specific warranty terms may vary by region and seller.

If you require technical assistance, spare parts, or have questions not covered in this manual, please contact your authorized Pedrollo dealer or customer support. When contacting support, please have your pump's model number (UPm2/3-GE) and item number (48SP2115A1) readily available.