ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat User Manual

Uvod

This manual provides detailed instructions for the installation, operation, and maintenance of your ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat. This thermostat is designed for use with single-stage heating systems and features a backlit display for easy readability. Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or your heating system.

Varnostne informacije

• Always turn off power to the heating system at the main fuse or circuit breaker panel before installing or servicing the thermostat.
• This thermostat is designed for 24 VAC heating systems only. Do not use it with line voltage sistemi (120/240 V AC).
• Če ste glede katerega koli koraka negotovi, naj namestitev opravi usposobljen tehnik.
• Ne povzročajte kratkega stika na poljih akumulatorja.
• Baterije zavrzite v skladu z lokalnimi predpisi.

Vsebina paketa

• ICM Controls SC1600L Thermostat Control Unit
• Pritrdilni material (vijaki in stenski sidri)
• Uporabniški priročnik

Nastavitev in namestitev

1. Izbira lokacije

Install the thermostat approximately 5 feet (1.5 meters) above the floor in an area with good air circulation. Avoid locations near heat sources (lampsončna svetloba, kamini), hladni prepih (okna, vrata) ali območja s slabim kroženjem zraka.

2. Odklop električne energije

Before beginning installation, ensure the power to your heating system is completely turned off at the circuit breaker or fuse box.

3. Odstranitev starega termostata

1. Previdno odstranite pokrov starega termostata.
2. Note the wire connections. This thermostat is designed for 2-wire heat-only systems. Typically, these wires are connected to terminals labeled 'R' and 'W'. Take a picture or label the wires for reference.
3. Odklopite žice in odstranite staro montažno ploščo termostata s stene.

4. Montaža novega termostata

1. Separate the front cover from the backplate of the SC1600L thermostat.
2. Position the backplate against the wall, feeding the wires through the opening. Mark the mounting holes.
3. Drill pilot holes if necessary and secure the backplate to the wall using the provided screws.

5. Ožičenje

Connect the two heating system wires to the terminals on the SC1600L backplate. This thermostat typically uses two wires: one for power (often labeled 'R' or 'Rh') and one for the heating call (often labeled 'W'). Ensure connections are secure.

6. Namestitev baterije

This thermostat is battery-powered. Insert the required batteries (typically 2 AA batteries, not included) into the battery compartment on the back of the front cover, observing the correct polarity (+/-). The display should illuminate.

7. Attaching the Front Cover

Carefully align the front cover with the mounted backplate and snap it into place.

Image: The ICM Controls SC1600L thermostat installed on a wall, showing its digital display and control buttons.

8. Power Restoration

Restore power to your heating system at the main fuse or circuit breaker panel.

Navodila za uporabo

1. Prikaz čezview

The large digital display shows the current room temperature. When adjusting the setpoint, the desired temperature will be displayed temporarily.

2. Nastavitev temperature

• Uporabite UP (▲) in DOL (▼) arrow buttons located next to the display to adjust the desired temperature (setpoint).
• Each press of the button will change the setpoint by one degree Fahrenheit.
• Termostat bo samodejno vzdrževal nastavljeno temperaturo.

3. System Mode Switch (Off/Heat)

Locate the slide switch at the bottom of the thermostat. This switch controls the system mode:

• IZKLOPLJENO: The heating system is turned off. The thermostat will not call for heat.
• TOPLOTA: The thermostat will operate the heating system to maintain the set temperature.

4. Delovanje osvetlitve ozadja

The display backlight will activate when any button is pressed, providing improved visibility in low-light conditions. The backlight will automatically turn off after a short period of inactivity.

Slika: Podrobna view of the SC1600L thermostat's controls and display.

Vzdrževanje

1. Zamenjava baterije

The thermostat is battery-powered. When the battery icon appears on the display, it indicates that the batteries are low and need to be replaced. To replace batteries:

1. Gently pull the front cover of the thermostat away from the wall plate.
2. Remove the old batteries and insert new ones, ensuring correct polarity.
3. Snap the front cover back onto the wall plate.

Opomba: Replacing batteries typically does not affect the set temperature, but it is good practice to verify the setting after replacement.

2. Čiščenje

Zunanjost termostata očistite z mehko krpoamp krpo. Ne uporabljajte abrazivnih čistil ali topil. Izogibajte se neposrednemu pršenju tekočin na termostat.

Odpravljanje težav

Specifikacije

• Model: SC1600L
• Znamka: Kontrole ICM
• Vrsta nadzora: Neprogramabilno
• Vrsta nadzora temperature: Ogrevanje
• vir energije: Napajanje na baterije
• voltage: 24 volta
• Vrsta zaslona: LCD z osvetlitvijo ozadja
• Nadzorna metoda: Nadzor gumbov
• Vrsta materiala: Plastika
• Vrsta pritrditve: Panelni nosilec

Informacije o garanciji

ICM Controls products are manufactured to high standards and are backed by a limited warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your product or visit the official ICM Controls webspletnega mesta. Shranite dokazilo o nakupu za uveljavljanje garancije.

Podpora

If you have any questions or require technical assistance with your ICM Controls SC1600L thermostat, please contact ICM Controls customer support. Contact information can typically be found on the product packaging or the official ICM Controls webmesto.